Next-in-Thread Next Message

Sad 3Com 3CCFE575 

Forum: 3Com PCMCIA Ethernet Adapter Issues
Date: 2000, Jan 18
From: Cristian Grigoriu grig

Hello everybody,

I'm having a terrible time setting up PCMCIA on my Fujitsu
LifeBook 585Tx. The problem is even if everything seems ok,
when trying to ping I get first a series of "Destination
Host Unreachable" then
"eth0: transmit timed out, tx_status 00 status e681.
 eth0: Interrupt posted but not delivered -- IRQ blocked by another device?"
then I get replies after 35 to 5 seconds (35000 - 5000 ms).

Here come the dumps: "/etc/sysconfig/pcmcia" PCMCIA=yes PCIC=i82365 PCIC_OPTS= CORE_OPTS= PCI_INT=1 PCI_CSC=1

"/etc/pcmcia/config.opts"

#
# Local PCMCIA Configuration File
#
# System resources available for PCMCIA devices
#
include irq 11 include port 0x1080-0x10ff include memory 0x04000000-0x04040fff
#
# Extra port range for IBM Token Ring
#
# include port 0xa00-0xaff
#
# Resources we should not use, even if they appear to be available
#
# First built-in serial port
exclude irq 4 # Second built-in serial port exclude irq 3 # First built-in parallel port exclude irq 7 exclude irq 0 exclude irq 1 exclude irq 2 exclude irq 5 exclude irq 6 exclude irq 8 exclude irq 10 #exclude irq 11 exclude irq 12 exclude irq 13 exclude irq 14 exclude irq 15
#
# Examples of options for loadable modules
#
# To fix sluggish network with IBM ethernet adapter...
#module "pcnet_cs" opts "mem_speed=600"
#
# Options for Xircom Netwave driver...
#module "netwave_cs" opts "domain=0x100 scramble_key=0x0"
#
# Options for IBM Token Ring adapters
#module "ibmtr_cs" opts "mmiobase=0xd0000 srambase=0xd4000"

"/etc/pcmcia/network.opts"
# Network Device Configuration
#
# The address format is "scheme,socket,instance".
#
case "$ADDRESS" in
*,*,*,*)
    IF_PORT="100baseT4"
    PUMP="n"
    BOOTP="n"
    DHCP="n"
    IPADDR="192.168.1.236"
    NETMASK="255.255.255.0"
    BROADCAST="192.168.1.255"
    NETWORK="192.168.1.0"
    GATEWAY="192.168.1.236"
    DOMAIN="tofan.ro"
    DNS_1="192.168.1.237"
    DNS_2="192.168.1.2"
    ;;
esac

"dmesg"
Linux version 2.2.12-20 (root@porky.devel.redhat.com) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Sep 27 10:25:54 EDT 1999
Detected 233866125 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 466.94 BogoMIPS
Memory: 62780k/65536k available (1008k kernel code, 412k reserved, 992k data, 64k init)
DENTRY hash table entries: 262144 (order: 9, 2097152 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Mobile Pentium MMX stepping 01
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Intel Pentium with F0 0F bug - workaround enabled.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfd9f0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Enabling I/O for device 00:0a
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 65536 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5 
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
Real Time Clock Driver v1.09
RAM disk driver initialized:  16 RAM disks of 4096K size
PIIX4: IDE controller on PCI bus 00 dev 09
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DTCA-24090, ATA DISK drive
hdc: UJDA110, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: IBM-DTCA-24090, 3909MB w/468kB Cache, CHS=993/128/63
hdc: ATAPI 14X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.56
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
   pII_mmx   :   352.425 MB/sec
   p5_mmx    :   421.005 MB/sec
   8regs     :   253.365 MB/sec
   32regs    :   188.214 MB/sec
using fastest function: p5_mmx (421.005 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
 hda: hda1 hda2 < hda5 hda6 >
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem).
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 64k freed
Adding Swap: 16088k swap-space (priority -1)
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
SB 3.01 detected OK (220)
ESS chip ES1878 detected
YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996
Linux PCMCIA Card Services 3.0.14
  kernel build: 2.2.12-20 #1 Mon Sep 27 10:25:54 EDT 1999
  options:  [pci] [cardbus] [apm]
Intel PCIC probe: 
  O2Micro OZ6832 PCI-to-CardBus at bus 0 slot 16, mem 0x68000000, 2 sockets
    host opts [0]: [a 40] [b 01] [c 00] [d 02] [mhpg 18] [fifo 00] [e 02] [no pci irq] [lat 168/176] [bus 32/34]
    host opts [1]: [a 40] [b 01] [c 50] [d 02] [mhpg 18] [fifo 00] [e 02] [no pci irq] [lat 168/176] [bus 35/37]
    ISA irqs (default) = 3,4,7,10,11,12 polling interval = 1000 ms
cs: IO port probe 0x1080-0x10ff: clean.
unloading PCMCIA Card Services
Linux PCMCIA Card Services 3.0.14
  kernel build: 2.2.12-20 #1 Mon Sep 27 10:25:54 EDT 1999
  options:  [pci] [cardbus] [apm]
Intel PCIC probe: 
  O2Micro OZ6832 PCI-to-CardBus at bus 0 slot 16, mem 0x68000000, 2 sockets
    host opts [0]: [a 40] [b 01] [c 00] [d 02] [mhpg 18] [fifo 00] [e 02] [no pci irq] [lat 168/176] [bus 32/34]
    host opts [1]: [a 40] [b 01] [c 50] [d 02] [mhpg 18] [fifo 00] [e 02] [no pci irq] [lat 168/176] [bus 35/37]
    ISA irqs (default) = 3,4,7,10,11 polling interval = 1000 ms
cs: IO port probe 0x1080-0x10ff: clean.
3c59x.c:v0.99L 5/28/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
cs: cb_config(bus 32): vendor 0x10b7, device 0x5157
  fn 0 bar 1: io 0x1080-0x10ff
  fn 0 bar 2: mem 0x4021000-0x402107f
  fn 0 bar 3: mem 0x4020000-0x402007f
  fn 0 rom: mem 0x4000000-0x401ffff
cs: cb_enable(bus 32)
  bridge io map 0 (flags 0x21): 0x1080-0x10ff
  bridge mem map 0 (flags 0x1): 0x4000000-0x4021fff
vortex_attach(bus 32, function 0, device 5157)
eth0: 3Com 3CCFE575 Cyclone CardBus at 0x1080,  00:10:4b:a5:87:ad, IRQ 11
eth0: CardBus functions mapped 04020000->c4856000
  8K byte-wide RAM 5:3 Rx:Tx split, MII interface.
  MII transceiver found at address 0, status 7809.
  Enabling bus-master transmits and whole-frame receives.
cat uses obsolete /proc/pci interface

"cat /proc/interrupts"
           CPU0       
  0:     154397          XT-PIC  timer
  1:        549          XT-PIC  keyboard
  2:          0          XT-PIC  cascade
  5:          1          XT-PIC  soundblaster
  8:          1          XT-PIC  rtc
 11:          2          XT-PIC  eth0
 12:         12          XT-PIC  PS/2 Mouse
 13:          1          XT-PIC  fpu
 14:      46621          XT-PIC  ide0
 15:          4          XT-PIC  ide1
NMI:          0

"cat /proc/pci"
PCI devices found:
  Bus 32, device   0, function  0:
    Ethernet controller: 3Com Unknown device (rev 1).
      Vendor id=10b7. Device id=5157.
      Medium devsel.  IRQ 11.  
      Non-prefetchable 32 bit memory at 0x1080 [0x1080].
      Non-prefetchable 32 bit memory at 0x4021000 [0x4021000].
      Non-prefetchable 32 bit memory at 0x4020000 [0x4020000].
  Bus  0, device   0, function  0:
    Host bridge: Intel 82439TX (rev 1).
      Medium devsel.  Master Capable.  Latency=32.  
  Bus  0, device   1, function  0:
    ISA bridge: Intel 82371AB PIIX4 ISA (rev 1).
      Medium devsel.  Fast back-to-back capable.  Master Capable.  No bursts.  
  Bus  0, device   1, function  1:
    IDE interface: Intel 82371AB PIIX4 IDE (rev 1).
      Medium devsel.  Fast back-to-back capable.  Master Capable.  Latency=64.  
      I/O at 0xfcf0 [0xfcf1].
  Bus  0, device   1, function  2:
    USB Controller: Intel 82371AB PIIX4 USB (rev 1).
      Medium devsel.  Fast back-to-back capable.  Master Capable.  Latency=64.  
      I/O at 0xfcc0 [0xfcc1].
  Bus  0, device   1, function  3:
    Bridge: Intel 82371AB PIIX4 ACPI (rev 1).
      Medium devsel.  Fast back-to-back capable.  
  Bus  0, device  16, function  0:
    CardBus bridge: O2 Micro 6832 (rev 2).
      Medium devsel.  Master Capable.  No bursts.  Min Gnt=128.Max Lat=4.
  Bus  0, device  16, function  1:
    CardBus bridge: O2 Micro 6832 (rev 2).
      Medium devsel.  Master Capable.  No bursts.  Min Gnt=128.Max Lat=4.
  Bus  0, device  20, function  0:
    VGA compatible controller: Trident TG 9660 / Cyber9385 (rev 211).
      Medium devsel.  Fast back-to-back capable.  IRQ 9.  
      Non-prefetchable 32 bit memory at 0xfe400000 [0xfe400000].
      Non-prefetchable 32 bit memory at 0xfedf0000 [0xfedf0000].
      Non-prefetchable 32 bit memory at 0xfe800000 [0xfe800000].

"cat /proc/ioports" 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-007f : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0220-022f : soundblaster 0376-0376 : ide1 0388-038b : Yamaha OPL3 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial(auto) 1080-10ff : cb_enabler fcf0-fcf7 : ide0 fcf8-fcff : ide1

"cat /proc/modules" 3c575_cb 18792 2 cb_enabler 2104 2 [3c575_cb] ds 5740 2 [cb_enabler] i82365 22640 2 pcmcia_core 39912 0 [cb_enabler ds i82365] opl3 11208 0 (unused) sb 33620 0 uart401 5968 0 [sb] sound 57240 0 [opl3 sb uart401] soundlow 300 0 [sound] soundcore 2372 5 [sb sound]

"cardctl config"
Socket 0:
  Vcc = 3.3, Vpp1 = 3.3, Vpp2 = 3.3
  Interface type is cardbus
  IRQ 11 is exclusive, level mode, enabled
  Function 0:
    I/O window 1: 0x1080 to 0x10ff, 32 bit
Socket 1:
  not configured

"/sbin/ifconfig"
eth0      Link encap:Ethernet  HWaddr 00:10:4B:A5:87:AD  
          inet addr:192.168.1.236  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:172 errors:0 dropped:0 overruns:571 frame:0
          TX packets:70 errors:4 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          Interrupt:11 Base address:0x1080 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:3924  Metric:1
          RX packets:52 errors:0 dropped:0 overruns:0 frame:0
          TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 

ANY help is highly appreciated.

Cristian Grigoriu

Next-in-Thread Next Message

Messages Inline: 0 1

None It's an O2Micro bridge issue, maybe fixed in latest drivers

Re: Sad 3Com 3CCFE575 (Cristian Grigoriu)
Date: 2000, Jan 21
From: David Hinds <dhinds@pcmcia.sourceforge.org>

Try building the latest beta driver package (on sourceforge.org in
/pcmcia/NEW).

-- Dave

Disagree Same problem with kernel 2.2.14 & pcmcia-cs 3.1.14

Re: None It's an O2Micro bridge issue, maybe fixed in latest drivers (David Hinds)
Date: 2000, Apr 20
From: Gregory Ade <gkade@bigbrother.net>

I have almost identical problems to this using the latest version of pcmcia-cs with 2.2.14 on my own Dell Inspiron 3500 w/ 3CCFE575BT-D. I was trying to figure out what on earth could be the problem, since I don't have any difficulty on the 10MHz ethernet at the office, but no end of troubles on my 10/100 MHz hub at home.

Unfortunately, I left my notebook at the office, so I can't get any data from it right now. But, it's essentially the same as the previous post. I'll post later if requested.

I can say that I'm excluding IRQ's 4, 5 and 7, the TI Cardbus (and both cards in it) run at IRQ 10.

Question Untitled

Re: Sad 3Com 3CCFE575 (Cristian Grigoriu)
Date: 2000, Feb 15
From: Cristian Grigoriu grig

I have installed the latest (February, 14th) PCMCIA package. I still have the same problem. However, when using a borrowed 16 bit PC-Card, everything's working fine. What should I do? Wait for my O2 Micro issue to be fixed or should I buy a new adapter? If I buy a new PC Card, should it be CardBus or 16 bit? I mean, will I have that problem with any other CardBus adapter? I would like to buy a CardBus one because of its advantages.

Any ideas?

Thanks, Cristian Grigoriu

Feedback system log messages with the 14-Feb-00 drivers

Re: Sad 3Com 3CCFE575 (Cristian Grigoriu)
Date: 2000, Feb 16
From: Cristian Grigoriu grig

First I have boot-up Win98 and that's what I've found:
O2Micro OZ6832/6833 CardBus Controller:
The resources this device is using do not
match any of its known configurations. To
assign resources manually for this device,
click Set Configuration Manually.

Input/Output Range	1080 - 10FF
Memory Range		04020000 - 04040FFF
Interrupt Request	09
Memory Range		04001000 - 04001FFF

3Com Megahertz 10/100 LAN CardBus PC Card
Interrupt Request	09
Memory Range		04040000 - 0404007F
Memory Range		04040080 - 040400FF
Input/Output Range	1080 - 10FF
Memory Range		04020000 - 0403FFFF

Then, I have boot-up RedHat 6.1, /etc/rc.d/init.d/pcmcia
restart, ping 192.168.1.1:

dmesg:
Linux version 2.2.12-20 (root@porky.devel.redhat.com) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Sep 27 10:25:54 EDT 1999
Detected 233866685 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 466.94 BogoMIPS
Memory: 62780k/65536k available (1008k kernel code, 412k reserved, 992k data, 64k init)
DENTRY hash table entries: 262144 (order: 9, 2097152 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Mobile Pentium MMX stepping 01
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Intel Pentium with F0 0F bug - workaround enabled.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfd9f0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Enabling I/O for device 00:0a
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 65536 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5 
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
Real Time Clock Driver v1.09
RAM disk driver initialized:  16 RAM disks of 4096K size
PIIX4: IDE controller on PCI bus 00 dev 09
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DTCA-24090, ATA DISK drive
hdc: UJDA110, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: IBM-DTCA-24090, 3909MB w/468kB Cache, CHS=993/128/63
hdc: ATAPI 14X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.56
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
   pII_mmx   :   352.425 MB/sec
   p5_mmx    :   421.005 MB/sec
   8regs     :   252.984 MB/sec
   32regs    :   188.214 MB/sec
using fastest function: p5_mmx (421.005 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
 hda: hda1 hda2 < hda5 hda6 >
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem).
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 64k freed
Adding Swap: 16088k swap-space (priority -1)
Linux PCMCIA Card Services 3.1.11
  kernel build: 2.2.12-20 #1 Mon Sep 27 10:25:54 EDT 1999
  options:  [pci] [cardbus] [apm] [pnp]
PCI routing table version 1.0 at 0xfdf70
  00:10.0 -> irq 9
  00:10.1 -> irq 9
PnP: PNP BIOS installation structure at 0xc00f6930
PnP: PNP BIOS version 1.0, entry at f0000:aa15, dseg at 400
Intel PCIC probe: 
  Bridge register mapping failed: check cb_mem_base setting
not found.
ds: no socket drivers loaded!
Intel PCIC probe: 
  O2Micro OZ6832/OZ6833 PCI-to-CardBus at slot 00:10, mem 0x68000000
    host opts [0]: [a 40] [b 01] [c 00] [d 02] [mhpg 18] [fifo 00] [e 02] [pci irq 9] [lat 168/176] [bus 35/37]
    host opts [1]: [a 40] [b 01] [c 50] [d 02] [mhpg 18] [fifo 00] [e 02] [pci irq 9] [lat 168/176] [bus 38/40]
    ISA irqs (default) = 3,4,5,7,10,11 PCI status changes
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x300-0x307 0x378-0x37f 0x388-0x38f
cs: IO port probe 0x0a00-0x0aff: clean.
cs: cb_alloc(bus 38): vendor 0x10b7, device 0x5157
3c59x.c:v0.99L 5/28/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
cs: cb_config(bus 38)
  fn 0 bar 1: io 0x280-0x2ff
  fn 0 bar 2: mem 0x60021000-0x6002107f
  fn 0 bar 3: mem 0x60020000-0x6002007f
  fn 0 rom: mem 0x60000000-0x6001ffff
cs: cb_enable(bus 38)
  bridge io map 0 (flags 0x21): 0x280-0x2ff
  bridge mem map 0 (flags 0x1): 0x60000000-0x60021fff
vortex_reap()
vortex_attach(bus 38, function 0, device 5157)
eth0: 3Com 3CCFE575 Cyclone CardBus at 0x280,  00:10:4b:a5:87:ad, IRQ 9
eth0: CardBus functions mapped 60020000->c4829000
  8K byte-wide RAM 5:3 Rx:Tx split, MII interface.
  MII transceiver found at address 0, status 7809.
  Enabling bus-master transmits and whole-frame receives.
eth0: transmit timed out, tx_status 00 status e681.
eth0: Interrupt posted but not delivered -- IRQ blocked by another device?
  Flags; bus-master 1, full 0; dirty 16 current 16.
  Transmit list 00000000 vs. c3ff0200.
  0: @c3ff0200  length 8000002a status 8001002a
  1: @c3ff0210  length 8000002a status 8001002a
  2: @c3ff0220  length 8000002a status 8001002a
  3: @c3ff0230  length 8000002a status 8001002a
  4: @c3ff0240  length 8000002a status 8001002a
  5: @c3ff0250  length 8000002a status 8001002a
  6: @c3ff0260  length 8000002a status 8001002a
  7: @c3ff0270  length 8000002a status 8001002a
  8: @c3ff0280  length 8000002a status 8001002a
  9: @c3ff0290  length 8000002a status 8001002a
  10: @c3ff02a0  length 8000002a status 8001002a
  11: @c3ff02b0  length 8000002a status 8001002a
  12: @c3ff02c0  length 8000002a status 8001002a
  13: @c3ff02d0  length 8000002a status 8001002a
  14: @c3ff02e0  length 8000002a status 8001002a
  15: @c3ff02f0  length 8000002a status 8001002a
eth0: Resetting the Tx ring pointer.

/sbin/ifconfig:
eth0      Link encap:Ethernet  HWaddr 00:10:4B:A5:87:AD  
          inet addr:192.168.1.236  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:200 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          Interrupt:9 Base address:0x280 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:3924  Metric:1
          RX packets:35 errors:0 dropped:0 overruns:0 frame:0
          TX packets:35 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 


cat /etc/sysconfig/pcmcia:
PCMCIA=yes
PCIC=i82365
PCIC_OPTS=
CORE_OPTS=
CARDMGR_OPTS=

cat /etc/pcmcia/config.opts:
#
# Local PCMCIA Configuration File
#
#----------------------------------------------------------------------

# System resources available for PCMCIA devices

include port 0x100-0x4ff, port 0x800-0x8ff, port 0xc00-0xcff
include memory 0xc0000-0xfffff
include memory 0xa0000000-0xa0ffffff, memory 0x60000000-0x60ffffff

# High port numbers do not always work...
# include port 0x1000-0x17ff

# Extra port range for IBM Token Ring
include port 0xa00-0xaff

# Resources we should not use, even if they appear to be available

# First built-in serial port
exclude irq 4
# Second built-in serial port
#exclude irq 3
# First built-in parallel port
exclude irq 7

#----------------------------------------------------------------------

# Examples of options for loadable modules

# To fix sluggish network with IBM ethernet adapter...
#module "pcnet_cs" opts "mem_speed=600"

# Options for IBM Token Ring adapters
#module "ibmtr_cs" opts "mmiobase=0xd0000 srambase=0xd4000"

# Options for Raylink/WebGear driver: uncomment only one line...
# Generic ad-hoc network
module "ray_cs" opts "pc_debug=1 essid=ADHOC_ESSID hop_dwell=128 beacon_period=256 translate=1"
# Infrastructure network for older cards
#module "ray_cs" opts "pc_debug=1 net_type=1 essid=ESSID1"
# Infrastructure network for WebGear
#module "ray_cs" opts "pc_debug=1 net_type=1 essid=ESSID1 translate=1 hop_dwell=128 beacon_period=256"

# Options for WaveLAN/IEEE driver (AccessPoint mode)...
#module "wvlan_cs" opts "station_name=MY_PC"
# Options for WaveLAN/IEEE driver (ad-hoc mode)...
#module "wvlan_cs" opts "port_type=3 channel=1 station_name=MY_PC"

# Options for Xircom Netwave driver...
#module "netwave_cs" opts "domain=0x100 scramble_key=0x0"

cat /etc/pcmcia/network.opts:
# Network adapter configuration
#
# The address format is "scheme,socket,instance,hwaddr".
#
# Note: the "network address" here is NOT the same as the IP address.
# See the Networking HOWTO.  In short, the network address is the IP
# address masked by the netmask.
#
case "$ADDRESS" in
*,*,*,*)
    INFO="Sample private network setup"
    # Transceiver selection, for some cards -- see 'man ifport'
    IF_PORT=""
    # Use BOOTP (via /sbin/bootpc, or /sbin/pump)? [y/n]
    BOOTP="n"
    # Use DHCP (via /sbin/dhcpcd, /sbin/dhclient, or /sbin/pump)? [y/n]
    DHCP="n"
    # Host's IP address, netmask, network address, broadcast address
    IPADDR="192.168.1.236"
    NETMASK="255.255.255.0"
    NETWORK="192.168.1.0"
    BROADCAST="192.168.1.255"
    # Gateway address for static routing
    GATEWAY="192.168.1.236"
    # Things to add to /etc/resolv.conf for this interface
    DOMAIN=""
    SEARCH=""
    DNS_1=""
    DNS_2=""
    DNS_3=""
    # NFS mounts, should be listed in /etc/fstab
    MOUNTS=""
    # For IPX interfaces, the frame type and network number
    IPX_FRAME=""
    IPX_NETNUM=""
    # Extra stuff to do after setting up the interface
    start_fn () { return; }
    # Extra stuff to do before shutting down the interface
    stop_fn () { return; }
    ;;
esac

cardctl config:
Socket 0:
  not configured
Socket 1:
  Vcc 3.3V  Vpp1 3.3V  Vpp2 3.3V
  interface type is "cardbus"
  irq 9 [exclusive] [level]
  function 0:
    io 0x0280-0x02ff [32bit]
3Com 3CCFE575


Add Message to: "3Com 3CCFE575"

Members Subscribe Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10