Next-in-Thread Next Message

Question More Info 

Forum: 3Com PCMCIA Ethernet Adapter Issues
Re: Question 3CCFEM656 (Alex Pearsall)
Re: Question Another 656 question. (Hunter Ware)
Date: 2000, Feb 03
From: Hunter Ware HunterWare

a bit more info...

on thos slow uploads from the machine I notice the net traffic (as reported by a graphical network monitor) is periodic. For a bit less then a second I get a spurt, and then I get a period of no traffic for a couple secs. This process repeats to give an average tx speed of about 5kB/s. This is vs. my average download speed of 500kB/s.

My dmesg gives this after startup...
Linux PCMCIA Card Services 3.1.9
  kernel build: 2.2.14 #3 Thu Jan 27 18:01:39 EST 2000
  options:  [pci] [cardbus] [apm] [pnp]
PCI routing table version 1.0 at 0xfdf60
  00:04.0 -> irq 11
  00:04.1 -> irq 11
PnP: PNP BIOS installation structure at 0xc00f6e60
PnP: PNP BIOS version 1.0, entry at f0000:b3ba, dseg at 400
Intel PCIC probe:
  TI 1220 PCI-to-CardBus at slot 00:04, mem 0x68000000
    host opts [0]: [serial pci & irq] [pci irq 11] [lat 168/176] [bus 32/34]
    host opts [1]: [serial pci & irq] [pci irq 11] [lat 168/176] [bus 35/37]
    ISA irqs (scanned) = 3,4,7,9,10 PCI status changes
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f
cs: IO port probe 0x0a00-0x0aff: clean.
cs: cb_alloc(bus 35): vendor 0x10b7, device 0x6560
3c59x.c:v0.99L 5/28/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
cs: cb_config(bus 35)
  fn 0 bar 1: io 0xa80-0xaff
  fn 0 bar 2: mem 0x60023000-0x6002307f
  fn 0 bar 3: mem 0x60022000-0x6002207f
  fn 1 bar 1: io 0xa00-0xa7f
  fn 1 bar 2: mem 0x60021000-0x6002107f
  fn 1 bar 3: mem 0x60020000-0x6002007f
  fn 0 rom: mem 0x60000000-0x6001ffff
cs: cb_enable(bus 35)
  bridge io map 0 (flags 0x21): 0xa00-0xaff
  bridge mem map 0 (flags 0x1): 0x60000000-0x60023fff
vortex_reap()
vortex_attach(bus 35, function 0, device 6560)
eth0: 3Com 3CCFE656 Cyclone CardBus at 0xa80,  00:10:5a:93:24:c8, IRQ 11
eth0: CardBus functions mapped 60022000->c8839000
  8K byte-wide RAM 5:3 Rx:Tx split, MII interface.
  MII transceiver found at address 0, status 7809.
  Enabling bus-master transmits and whole-frame receives.
eth0: Transmit error, Tx status register 90.
cat uses obsolete /proc/pci interface

Thanks again for any help,
		Hunter

Next-in-Thread Next Message

Add Message to: "More Info"

Members Subscribe Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10