Next-in-Thread Next Message

Question PCMCIA ATA/IDE card detected but not mounted 

Forum: PCMCIA ATA/IDE Device Issues
Date: 2000, Feb 04
From: Achim Spangler spangler

System:
* SUSE 6.3
* kernel 2.2.14
* pcmcia 3.1.10
* SunDisk SDP3B-4, ATA DISK drive

If I insert the mentioned ATA disk in my pcmcia 1 slot (network card in slot 0), I hear TWO high beeps (all o.k.). But the msdos filesystem on hde1 is not automatically mounted.

IMPORTANT: Later manually mounting "by hand" ("mount /dev/hde1") allow me to mount and access the drive -> only the automatic mount doesn't work

Gratulation: With an earlier version of kernel and pcmcia I had to remove my network card before inserting the ide card, because all irq's was used. But now pcmcia can use not active used irq (occupied by inactive systems like serial port). ==> THANKS

Looking in /var/log/messages I get the following: -------------------------------------------------

kernel: Linux PCMCIA Card Services 3.1.10
kernel:   kernel build: 2.2.14 #2 Mon Jan 10 10:46:39 CET 2000
kernel:   options:  [pci] [cardbus] [apm]
kernel: PCI routing table version 1.0 at 0xfe840
kernel: Intel PCIC probe: 
kernel:   TI 1225 PCI-to-CardBus at slot 00:0a, mem 0x68000000
kernel:     host opts [0]: [serial pci & irq] [no pci irq] [lat 168/176] [bus 32/34]
kernel:     host opts [1]: [serial pci & irq] [no pci irq] [lat 168/176] [bus 35/37]
kernel:     ISA irqs (scanned) = 3,4,7,9,11 polling interval = 1000 ms
cardmgr[1815]: starting, version is 3.1.10

cardmgr[1815]: watching 2 sockets

kernel: cs: IO port probe 0x1000-0x17ff: excluding 0x1000-0x103f 0x1400-0x140f
kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x378-0x37f 0x4d0-0x4d7
kernel: cs: IO port probe 0x0a00-0x0aff: clean.
cardmgr[1815]: initializing socket 0 kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. cardmgr[1815]: socket 0: 3Com 589 Ethernet

cardmgr[1815]: executing: 'insmod /lib/modules/2.2.14/pcmcia/3c589_cs.o'

kernel: eth0: 3Com 3c589, io 0x310, irq 3, hw_addr 00:60:08:BA:87:80
kernel:   8K FIFO split 5:3 Rx:Tx, auto xcvr
cardmgr[1815]: executing: './network start eth0'

cardmgr[1815]: + Shutting down INET services (inetd)^[[71G^[[32mdone^[[m

cardmgr[1815]: + Starting INET services (inetd)^[[71G^[[32mdone^[[m ...

cardmgr[1815]: initializing socket 1

cardmgr[1815]: socket 1: ATA/IDE Fixed Disk

cardmgr[1815]: executing: 'insmod /lib/modules/2.2.14/pcmcia/ide_cs.o'

kernel: hde: SunDisk SDP3B-4, ATA DISK drive
kernel: ide2 at 0x100-0x107,0x10e on irq 3
kernel: hde: SunDisk SDP3B-4, 3MB w/1kB Cache, CHS=123/2/32
kernel:  hde: hde1
kernel: ide_cs: hde: Vcc = 3.3, Vpp = 0.0
cardmgr[1815]: executing: './ide start hde'
kernel: VFS: Disk change detected on device ide2(33,0)
kernel:  hde: hde1
kernel: hde: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
kernel: hde: drive_cmd: error=0x04 { DriveStatusError }
-------------------------------------------------

My ide.opts:
-------------------------------------------------
case "$ADDRESS" in
*,*,*,1)
    DO_FSTAB="y" ; DO_FSCK="y" ; DO_MOUNT="y"
    FSTYPE="msdos"
    #OPTS=""
    MOUNTPT="/mnt/ide_pcmcia_1"
    ;;
*,*,*,2)
    DO_FSTAB="y" ; DO_FSCK="y" ; DO_MOUNT="y"
    FSTYPE="msdos"
    #OPTS=""
    MOUNTPT="/mnt/ide_pcmcia_2"
    ;;
*,*,*,*)
    PARTS="1"
    ;;
esac
-------------------------------------------------

The relevant lines in /etc/fstab: -------------------------------------------------

/dev/hde1 /mnt/ide_pcmcia_1 msdos noauto,rw,user,exec,suid,umask=000 0 0

/dev/hde2 /mnt/ide_pcmcia_2 msdos noauto,rw,user,exec,suid,umask=000 0 0

-------------------------------------------------

Achim

Next-in-Thread Next Message

Select this message: PCMCIA ATA/IDE card detected but not mounted

Messages Inline: 1 All Outline: 1 2 All

1. None Just a ide.opts glitch by David Hinds, 2000, Feb 04

Message Administration

This form allows you to delete, move, or copy one or more messages. You can move messages by copying and deleting the original. The action will be applied to the messages you select above and all replies to those selected messages.


If you want to copy or move messages, specify the HyperNews path of a destination forum or message that all messages will be copied or moved to. The destination must already exist, so maybe create it first.

Path of Destination (a Forum or Message): (e.g. "test")

Notify Subscribers at destination
NO


If you want to delete messages (the default), specify that here. If you want to move messages, you need to delete the original messages; placeholders will be left pointing to where they were moved.

Delete Messages
NO


Caution: After deleteing messages (the default), if you have not copied them (i.e. no destination above), then the selected messages are not be recoverable.

Members Subscribe No Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10
[ Edit This Forum ]