Thanks for the configuration info--the PCChost 1200 is working well except for interrupts. Is there something additional I must do to get CardBus interrupts to work with the PCChost 1200? With the no irq_mode defined, /proc/interrupts claims that my CardBus device(s) have irqs 3 and 5, but I am not convinced that things are working properly since /proc/interrupts tells me that 0 interrupts have occurred when I know several should have taken place. Further, my diagnostic tests on the interrupts never receive their expected interrupts, timing out long after the interrupts should have occurred.
On boot, I get the following:
Aug 10 15:03:52 shmack kernel: Linux PCMCIA Card Services 3.1.19 Aug 10 15:03:52 shmack kernel: kernel build: 2.2.5-15 #1 Mon Apr 19 23:00:46 EDT 1999 Aug 10 15:03:52 shmack kernel: options: [pci] [cardbus] [apm] Aug 10 15:03:52 shmack kernel: PCI routing table version 1.0 at 0xfdf30 Aug 10 15:03:52 shmack kernel: 00:0f.1 -> irq 9 Aug 10 15:03:52 shmack kernel: Intel PCIC probe: Aug 10 15:03:52 shmack kernel: TI 1220 rev 02 PCI-to-CardBus at slot 00:0f, mem 0x68000000 Aug 10 15:03:52 shmack kernel: host opts : [serial pci & irq] [no pci irq] [lat 168/176] [bus 32/34] Aug 10 15:03:52 shmack kernel: host opts : [serial pci & irq] [pci irq 9] [lat 168/176] [bus 35/37] Aug 10 15:03:52 shmack kernel: ISA irqs (default) = 3,4,5,7,10,12 polling interval = 1000 ms
I changed the irq_mode to 0,1,2,3 and no improvement, though, for mode 0, the controller could not assign any interrupts.
Before asking you, I asked Sycard about Linux support and here is something that may explain what needs to be done:
> 2. What is required to enable the PCChost 1200 for Linux? > > The HOST1200.SYS driver is used to initialize the PCI1220 CardBus controller > for use with > Windows 9x. HOST1200.SYS also configures the programmable I/O pins for use > with the > indicator LEDs, interrupt type and power switch chip (TPS2206). HOST1200.SYS > will do > this initialization on boot-up. HOST1200.SYS performs the following: > Enable PCIC Legacy address at 3E0H by setting PCI configuration space 44H = > 03E0 and 46H = 0000H. > Enable I/O and memory accesses by setting bits 0 and 1 in the PCI Command > register at offset 04H in PCI Configuration space. > Enable clock to external voltage switch chip (TPS2206) by setting bit 27 in > the System Control register at PCI configuration offset 80H. > Configure multifunction pins for PCChost 1200 by setting the multifunction > routing register at PCI configuration space offset 8CH to 1DC7H and offset > 8EH to 0007H. > Enable ExCA legacy interrupts by setting bit 7 in the bridge control register > at PCI configuration space offset 3EH. > A similar initialization routine will be required for Linux. Let know if you > have any questions or problems.
Unfortunately, I don't know the anatomy of the i82365.c module or any of the pcmcia-cs code well enough to implement any of these configuration steps without some hints. If these initialization steps aren't being taken care of by version 3.1.19, how might I add them (and where)?
Paul ================== firstname.lastname@example.org
[ Edit This Forum ]