Next-in-Thread Next Message

Warning 3.1.10 does no longer work on DELL Inspiron 7500 

Forum: PCMCIA Installation and Configuration Issues
Date: 2000, Feb 11
From: Ronny Bremer rbremer

Hardware: DELL Inspiron 7500

The PCMCIA release 3.1.8 works and gives the following message at startup:

Feb 11 08:56:27 fghamw07 kernel: Linux PCMCIA Card Services 3.1.8 
Feb 11 08:56:27 fghamw07 kernel:   kernel build: 2.2.14 #4 Wed Feb 9 09:28:40 CET 2000 
Feb 11 08:56:27 fghamw07 kernel:   options:  [pci] [cardbus] [apm] [pnp] 
Feb 11 08:56:27 fghamw07 kernel: PnP: PNP BIOS installation structure at 0xc00f7210 
Feb 11 08:56:27 fghamw07 kernel: PnP: PNP BIOS version 1.0, entry at f0000:a776, dseg at 400 
Feb 11 08:56:27 fghamw07 kernel: PCI routing table version 1.0 at 0xfdf50 
Feb 11 08:56:27 fghamw07 kernel:   00:04.0 -> irq 11 
Feb 11 08:56:27 fghamw07 kernel:   00:04.1 -> irq 11 
Feb 11 08:56:27 fghamw07 kernel: Intel PCIC probe:  
Feb 11 08:56:27 fghamw07 kernel:   TI 1225 PCI-to-CardBus at bus 0 slot 4, mem 0x68000000, 2 sockets 
Feb 11 08:56:27 fghamw07 kernel:     host opts [0]: [ring] [pwr save] [serial pci & irq] [pci irq 11] [lat 168/32] [bus 32/34] 
Feb 11 08:56:27 fghamw07 kernel:     host opts [1]: [ring] [pwr save] [serial pci & irq] [pci irq 11] [lat 168/32] [bus 35/37] 
Feb 11 08:56:27 fghamw07 kernel:     ISA irqs (scanned) = 9,10 polling interval = 1000 ms 
Feb 11 08:56:28 fghamw07 cardmgr[434]: starting, version is 3.1.8

When using 3.1.10 however, the output stops with the line:

ISA irqs (scanned) = 3,4,7,9,10

and the systems freezes. I cannot interrupt anything, it is dead stopped. I tried multiple times, same effect. As you can see, the list of detected interrupts did change, I do no know why, since my config files are identical (in terms of the excluded and included resources).

Any help would be appreciated.

Ronny

Next-in-Thread Next Message

Select this message: 3.1.10 does no longer work on DELL Inspiron 7500

Messages Inline: 1 All Outline: 1 2 3

1. Warning 3.1.9 / 3.1.10 Broken for IBM ThinkPad i1460 by Kenny Jansson, 2000, Feb 15
(_ Note PnP is enabled by Ronny Bremer, 2000, Feb 17
(_ Ok tried beta, works :) by Ronny Bremer, 2000, Feb 25

Message Administration

This form allows you to delete, move, or copy one or more messages. You can move messages by copying and deleting the original. The action will be applied to the messages you select above and all replies to those selected messages.


If you want to copy or move messages, specify the HyperNews path of a destination forum or message that all messages will be copied or moved to. The destination must already exist, so maybe create it first.

Path of Destination (a Forum or Message): (e.g. "test")

Notify Subscribers at destination
NO


If you want to delete messages (the default), specify that here. If you want to move messages, you need to delete the original messages; placeholders will be left pointing to where they were moved.

Delete Messages
NO


Caution: After deleteing messages (the default), if you have not copied them (i.e. no destination above), then the selected messages are not be recoverable.

Members Subscribe No Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10
[ Edit This Forum ]