Hi,
I installed the 22 Aug beta version but still the same prob,
simple pings are ok but ping of size 15000 and up don't pass
at all. Here are those logs you wanted to see:
:
Linux PCMCIA Card Services 3.1.20
kernel build: 2.2.15-4mdk #1 Wed May 10 15:31:30 CEST 2000
options: [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xfb230
unknown PCI interrupt router 1066:8002
Intel PCIC probe:
TI 1131 rev 01 PCI-to-CardBus at slot 00:09, mem 0x68000000
host opts [0]: [ring] [pci + serial irq] [no pci irq] [lat 168/176] [bus 32/
34]
host opts [1]: [ring] [pci + serial irq] [no pci irq] [lat 168/176] [bus 35/
37]
ISA irqs (scanned) = 3,4,7,9,10,11 status change on irq 11
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x230-0x23f 0x330-0x337 0x378-0x37f 0
x388-0x38f
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: cb_alloc(bus 35): vendor 0x10b7, device 0x6564
3c59x.c:v0.99Q 5/16/2000 Donald Becker, becker@scyld.com
http://www.scyld.com/network/vortex.html
cs: cb_config(bus 35)
fn 0 bar 1: io 0x1100-0x11ff
fn 0 bar 2: mem 0x60023000-0x6002307f
fn 0 bar 3: mem 0x60022000-0x6002207f
fn 1 bar 1: io 0x1000-0x10ff
fn 1 bar 2: mem 0x60021000-0x600210ff
fn 1 bar 3: mem 0x60020000-0x6002007f
fn 0 rom: mem 0x60000000-0x6001ffff
irq 3
cs: cb_enable(bus 35)
bridge io map 0 (flags 0x21): 0x1000-0x11ff
bridge mem map 0 (flags 0x1): 0x60000000-0x60023fff
vortex_attach(device 23:00.0)
eth0: 3Com 3CXFEM656C Tornado CardBus at 0x1100, 00:50:da:ac:95:4f, IRQ 3
product code 'VS' rev 10.00 date 06-12-00
eth0: CardBus functions mapped 60022000->c184c000.
8K byte-wide RAM 5:3 Rx:Tx split, MII interface.
MII transceiver found at address 0, status 7809.
Enabling bus-master transmits and whole-frame receives.
eth0: Setting full-duplex based on MII #0 link partner capability of 45e1.
eth0: transmit timed out, tx_status 00 status e000.
diagnostics: net 0ce0 media a800 dma 000000a0.
Flags; bus-master 1, full 1; dirty 68 current 78.
Transmit list 008d5a40 vs. c08d5a40.
0: @c08d5a00 length 800005ea status 800105ea
1: @c08d5a10 length 800005ea status 800105ea
2: @c08d5a20 length 800005ea status 800105ea
3: @c08d5a30 length 800005ea status 800105ea
4: @c08d5a40 length 800005ea status 800105ea
5: @c08d5a50 length 800004b2 status 800004b2
6: @c08d5a60 length 800005ea status 800005ea
7: @c08d5a70 length 800005ea status 800005ea
8: @c08d5a80 length 800005ea status 800005ea
9: @c08d5a90 length 800005ea status 800005ea
10: @c08d5aa0 length 800005ea status 800005ea
11: @c08d5ab0 length 800005ea status 800005ea
12: @c08d5ac0 length 800005ea status 800005ea
13: @c08d5ad0 length 800005ea status 800005ea
14: @c08d5ae0 length 800005ea status 800105ea
15: @c08d5af0 length 800005ea status 800105ea
eth0: Resetting the Tx ring pointer.
eth0: Tx Ring full, refusing to send buffer.
eth0: transmit timed out, tx_status 00 status e000.
diagnostics: net 0ce0 media a800 dma 000000a0.
Flags; bus-master 1, full 1; dirty 68 current 78.
Transmit list 008d5a40 vs. c08d5a40.
0: @c08d5a00 length 800005ea status 800105ea
1: @c08d5a10 length 800005ea status 800105ea
[ETC....]
this comes when I do a ping -s 15000 to the tower-pc.
I tried to touch the source of 3c575_cb.c to see if anything
could make it go a bit better but it didn't change a lot. It's
also my first network I set up. Is it possible to limit
something somewhere making it work, even if that makes the
network slow down?
Thanks for all the hard work!
Tom
|
Messages