Next-in-Thread Next Message

None Syslog dump 

Forum: PCMCIA Network Adapter Issues
Re: Question Hamlet FE1500 poor performance problem. (Alessandro De Salvo)
Re: None Need more detailed information (David Hinds)
Re: None More informations... (Alessandro De Salvo)
Date: 2000, Jul 20
From: Alessandro De Salvo desalvo

Here it is my syslog dump, but apparently everything is fine!!!

Jul 20 21:06:33 ads pcmcia: Starting PCMCIA services: 
Jul 20 21:06:33 ads pcmcia:  modules 
Jul 20 21:06:33 ads pcmcia:  cardmgr. 
Jul 20 21:06:33 ads rc: Starting pcmcia succeeded 
Jul 20 21:06:33 ads cardmgr[179]: starting, version is 3.1.8 
Jul 20 21:06:33 ads portmap: portmap startup succeeded 
Jul 20 21:06:33 ads sysctl: net.ipv4.ip_forward = 0 
Jul 20 21:06:33 ads sysctl: net.ipv4.conf.all.rp_filter = 1 
Jul 20 21:06:33 ads sysctl: net.ipv4.ip_always_defrag = 0 
Jul 20 21:06:33 ads sysctl: kernel.sysrq = 0 
Jul 20 21:06:33 ads network: Setting network parameters succeeded 
Jul 20 21:06:33 ads cardmgr[179]: initializing socket 0 <30>Jul 20 21:06:33 card
mgr[179]: socket 0: NE2000 Compatible Ethernet Jul 20 21:06:34 ads cardmgr[179]: executing: 'insmod/lib/modules/2.2.16-3/pcmcia/pcnet_cs.o'

Jul 20 21:06:34 ads network: Bringing up interface lo succeeded 
Jul 20 21:06:34 ads ifup: SIOCADDRT: File exists 
Jul 20 21:06:34 ads last message repeated 2 times
Jul 20 21:06:34 ads network: Bringing up interface eth0 succeeded 
Jul 20 21:06:34 ads nfslock: rpc.lockd startup succeeded 
Jul 20 21:06:34 ads nfslock: rpc.statd startup succeeded 

I tried also "test_network", and this is the output:

PCMCIA network settings are coming from linuxconf.

Checking network interface eth0 (pcnet_cs driver):

  Kernel messages for eth0:
  eth0: NE2000 Compatible: io 0x300, irq 9, hw_addr 00:E0:98:34:F0:0A
  eth0: found link beat
  eth0: lost link beat

  Current ifconfig settings:
  eth0      Link encap:Ethernet  HWaddr 00:E0:98:34:F0:0A  
            inet addr:137.138.102.76  Bcast:137.138.255.255  Mask:255.255.0.0
            UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
            RX packets:2317 errors:0 dropped:0 overruns:0 frame:0
            TX packets:541 errors:0 dropped:0 overruns:0 carrier:0
            collisions:3 txqueuelen:100 
            Interrupt:9 Base address:0x300 

  The interface is configured and running.
  RX and TX traffic both look ok.

  Enter a numeric IP address to ping: 137.138.1.1

  Pinging 137.138.1.1 ... response received!
  The device interrupt seems to be incrementing normally.

So, what I should conclude from here is that everything is fine, but... still only ~50 Kb/s of transfer rate. Any idea? Thanks

Next-in-Thread Next Message

Select this message: Syslog dump

Messages Inline: 1 All Outline: 1 2 All

1. None Maybe a driver upgrade will help by David Hinds, 2000, Jul 20
(_ None Upgrade done, but nothing different... by Alessandro De Salvo, 2000, Jul 21
(_ None Back to kernel 2.2.16-3. by Alessandro De Salvo, 2000, Jul 21
(_ None More syslog + other infos by Alessandro De Salvo, 2000, Jul 21
(_ None The problem appears to be only in RX by Alessandro De Salvo, 2000, Jul 24

Message Administration

This form allows you to delete, move, or copy one or more messages. You can move messages by copying and deleting the original. The action will be applied to the messages you select above and all replies to those selected messages.


If you want to copy or move messages, specify the HyperNews path of a destination forum or message that all messages will be copied or moved to. The destination must already exist, so maybe create it first.

Path of Destination (a Forum or Message): (e.g. "test")

Notify Subscribers at destination
NO


If you want to delete messages (the default), specify that here. If you want to move messages, you need to delete the original messages; placeholders will be left pointing to where they were moved.

Delete Messages
NO


Caution: After deleteing messages (the default), if you have not copied them (i.e. no destination above), then the selected messages are not be recoverable.

Members Subscribe No Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10
[ Edit This Forum ]