Next-in-Thread Next Message

None Syslog dump 

Forum: PCMCIA Network Adapter Issues
Re: Question Hamlet FE1500 poor performance problem. (Alessandro De Salvo)
Re: None Need more detailed information (David Hinds)
Re: None More informations... (Alessandro De Salvo)
Date: 2000, Jul 20
From: Alessandro De Salvo desalvo

Here it is my syslog dump, but apparently everything is fine!!!

Jul 20 21:06:33 ads pcmcia: Starting PCMCIA services: 
Jul 20 21:06:33 ads pcmcia:  modules 
Jul 20 21:06:33 ads pcmcia:  cardmgr. 
Jul 20 21:06:33 ads rc: Starting pcmcia succeeded 
Jul 20 21:06:33 ads cardmgr[179]: starting, version is 3.1.8 
Jul 20 21:06:33 ads portmap: portmap startup succeeded 
Jul 20 21:06:33 ads sysctl: net.ipv4.ip_forward = 0 
Jul 20 21:06:33 ads sysctl: net.ipv4.conf.all.rp_filter = 1 
Jul 20 21:06:33 ads sysctl: net.ipv4.ip_always_defrag = 0 
Jul 20 21:06:33 ads sysctl: kernel.sysrq = 0 
Jul 20 21:06:33 ads network: Setting network parameters succeeded 
Jul 20 21:06:33 ads cardmgr[179]: initializing socket 0 <30>Jul 20 21:06:33 card
mgr[179]: socket 0: NE2000 Compatible Ethernet Jul 20 21:06:34 ads cardmgr[179]: executing: 'insmod/lib/modules/2.2.16-3/pcmcia/pcnet_cs.o'

Jul 20 21:06:34 ads network: Bringing up interface lo succeeded 
Jul 20 21:06:34 ads ifup: SIOCADDRT: File exists 
Jul 20 21:06:34 ads last message repeated 2 times
Jul 20 21:06:34 ads network: Bringing up interface eth0 succeeded 
Jul 20 21:06:34 ads nfslock: rpc.lockd startup succeeded 
Jul 20 21:06:34 ads nfslock: rpc.statd startup succeeded 

I tried also "test_network", and this is the output:

PCMCIA network settings are coming from linuxconf.

Checking network interface eth0 (pcnet_cs driver):

  Kernel messages for eth0:
  eth0: NE2000 Compatible: io 0x300, irq 9, hw_addr 00:E0:98:34:F0:0A
  eth0: found link beat
  eth0: lost link beat

  Current ifconfig settings:
  eth0      Link encap:Ethernet  HWaddr 00:E0:98:34:F0:0A  
            inet addr:137.138.102.76  Bcast:137.138.255.255  Mask:255.255.0.0
            UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
            RX packets:2317 errors:0 dropped:0 overruns:0 frame:0
            TX packets:541 errors:0 dropped:0 overruns:0 carrier:0
            collisions:3 txqueuelen:100 
            Interrupt:9 Base address:0x300 

  The interface is configured and running.
  RX and TX traffic both look ok.

  Enter a numeric IP address to ping: 137.138.1.1

  Pinging 137.138.1.1 ... response received!
  The device interrupt seems to be incrementing normally.

So, what I should conclude from here is that everything is fine, but... still only ~50 Kb/s of transfer rate. Any idea? Thanks

Next-in-Thread Next Message

Messages Inline: 1 All Outline: 1 2 3

1. None Maybe a driver upgrade will help by David Hinds, 2000, Jul 20
(_ None Upgrade done, but nothing different... by Alessandro De Salvo, 2000, Jul 21
(_ None Back to kernel 2.2.16-3. by Alessandro De Salvo, 2000, Jul 21
(_ None More syslog + other infos by Alessandro De Salvo, 2000, Jul 21
(_ None The problem appears to be only in RX by Alessandro De Salvo, 2000, Jul 24

Add Message to: "Syslog dump"

Members Subscribe Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10