Next-in-Thread Next Message

Question To quick to be happy, seems to have some IRQ problem still 

Forum: PCMCIA Network Adapter Issues
Re: Question Psion GoldCard Cardbus Network adapter problem with Mandrake 7.1 (Jan Calmered)
Re: None IO port allocation problem (David Hinds)
Re: Feedback Thanks, allocating more IO helped (Jan Calmered)
Date: 2000, Aug 14
From: Jan Calmered <jan.calmered@sbs.siemens.se>

I still seem to have some IRQ problem. I understand that it might be an issue of the CardBus bridge of PCI and ISA.

The driver loads OK, everything seem fine except that I get a timeout trying to use the network, complaints about irq 9 failing. I have tried to set the PCIC_OPTS to irq_mode=0, and to set irq_list to different settings without luck

Below the log and the dump_pirq

Any ideas

Jan

Interrupt routing table found at address 0xf57d0:
  Version 1.0, size 0x00d0
  Interrupt router is device 00:07.0
  PCI exclusive interrupt mask: 0x0000

Device 00:01.0 (slot 0):
  INTA: link 0x60, irq mask 0xdef8
  INTB: link 0x61, irq mask 0xdef8
  INTC: link 0x62, irq mask 0xdef8
  INTD: link 0x63, irq mask 0xdef8

Device 00:07.0 (slot 0):
  INTA: link 0x60, irq mask 0xdef8
  INTB: link 0x61, irq mask 0xdef8
  INTC: link 0x62, irq mask 0xdef8
  INTD: link 0x63, irq mask 0xdef8

Device 00:06.0 (slot 0):

Device 00:0a.0 (slot 0):
  INTA: link 0x60, irq mask 0xdef8
  INTB: link 0x61, irq mask 0xdef8

Device 00:13.0 (slot 0):
  INTA: link 0x60, irq mask 0xdef8
  INTB: link 0x61, irq mask 0xdef8

Device 00:11.0 (slot 0):

Device ff:04.0 (slot 0):

Device ff:06.0 (slot 0):
  INTA: link 0x60, irq mask 0xdef8
  INTB: link 0x61, irq mask 0xdef8

Device ff:05.0 (slot 0):

Device ff:0e.0 (slot 2):
  INTA: link 0x61, irq mask 0xdef8
  INTB: link 0x60, irq mask 0xdef8

Device ff:0f.0 (slot 3):
  INTA: link 0x60, irq mask 0xdef8
  INTB: link 0x61, irq mask 0xdef8

Interrupt router at 00:07.0: Intel 82371AB PIIX4/PIIX4E PCI-to-ISA bridge
  PIRQ1 (link 0x60): irq 9
  PIRQ2 (link 0x61): irq 9
  PIRQ3 (link 0x62): unrouted
  PIRQ4 (link 0x63): irq 10
  Serial IRQ: [disabled] [quiet] [frame=21] [pulse=4]

dmesg

nobi.mandrakesoft.com) (gcc version 2.95.3 19991030 (prerelease)) #1 Wed May 10 15:31:30 CEST 2000
Detected 267277858 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 532.48 BogoMIPS
Memory: 192660k/196608k available (1208k kernel code, 416k reserved, 2252k data, 72k init, 0k bigmem)
Dentry hash table entries: 32768 (order 6, 256k)
Buffer cache hash table entries: 262144 (order 8, 1024k)
Page cache hash table entries: 65536 (order 6, 256k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium II (Deschutes) stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xf5200
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Enabling I/O for device 00:3a
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 262144 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5 
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.12)
Real Time Clock Driver v1.09
RAM disk driver initialized:  16 RAM disks of 4096K size
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xfcd8-0xfcdf, BIOS settings: hdc:pio, hdd:pio
hda: TOSHIBA MK1214GAP, ATA DISK drive
hdc: TOSHIBA CD-ROM XM-1602B, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: TOSHIBA MK1214GAP, 11513MB w/0kB Cache, CHS=1467/255/63
hdc: ATAPI 20X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.56
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
   pII_mmx   :   589.407 MB/sec
   p5_mmx    :   615.696 MB/sec
   8regs     :   477.774 MB/sec
   32regs    :   251.841 MB/sec
using fastest function: p5_mmx (615.696 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
 hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 >
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 72k freed
Adding Swap: 136512k swap-space (priority -1)
usb.c: registered new driver hub
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
usb.c: registered new driver keyboard
cs89x0.c: Module autoprobing not allowed.
cs89x0.c: Append io=0xNNN
Linux PCMCIA Card Services 3.1.19
  kernel build: 2.2.15-4mdk #1 Wed May 10 15:31:30 CEST 2000
  options:  [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xf57d0
  00:0a.0 -> irq 9
  00:0a.1 -> irq 9
Intel PCIC probe: 
  O2Micro OZ6832/33 rev 02 PCI-to-CardBus at slot 00:0a, mem 0x68000000
    host opts [0]: [pci irq 9] [lat 168/176] [bus 32/34]
    host opts [1]: [pci irq 9] [lat 168/176] [bus 35/37]
    PCI irq 9 test failed
    ISA irqs (default) = 3,4,5,7,11,12 polling interval = 1000 ms
cs89x0.c: Module autoprobing not allowed.
cs89x0.c: Append io=0xNNN
cs89x0.c: Module autoprobing not allowed.
cs89x0.c: Append io=0xNNN
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
  Error: Illegal request -- (Sense key=0x05)
  Invalid field in command packet -- (asc=0x24, ascq=0x00)
  The failed "Start Stop Unit" packet command was: 
  "1b 00 00 00 03 00 00 00 00 00 00 00 "
  Error in command packet byte 50047 bit 0
cdrom: open failed.
cs: socket 0 timed out during reset
end_request: I/O error, dev 02:00 (floppy), sector 0
end_request: I/O error, dev 02:00 (floppy), sector 0
end_request: I/O error, dev 02:00 (floppy), sector 0
end_request: I/O error, dev 02:00 (floppy), sector 0
FAT bread failed
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x807
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x378-0x37f 0x388-0x38f 0x398-0x39f 0x4d0-0x4d7
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
usb-uhci.c: $Revision: 1.228 $ time 15:46:55 May 10 2000
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: Intel USB controller: setting latency timer to 0
usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
unloading PCMCIA Card Services
Linux PCMCIA Card Services 3.1.19
  kernel build: 2.2.15-4mdk #1 Wed May 10 15:31:30 CEST 2000
  options:  [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xf57d0
Intel PCIC probe: 
  O2Micro OZ6832/33 rev 02 PCI-to-CardBus at slot 00:0a, mem 0x68000000
    host opts [0]: [pc/pci] [pci irq 9] [lat 168/176] [bus 32/34]
    host opts [1]: [pc/pci] [pci irq 9] [lat 168/176] [bus 35/37]
    PCI irq 9 test failed
    ISA irqs (default) = 3,4,5,7,11 polling interval = 1000 ms
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x807
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x378-0x37f 0x388-0x38f 0x398-0x39f 0x4d0-0x4d7
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: socket 0 timed out during reset
unloading PCMCIA Card Services
Linux PCMCIA Card Services 3.1.19
  kernel build: 2.2.15-4mdk #1 Wed May 10 15:31:30 CEST 2000
  options:  [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xf57d0
Intel PCIC probe: 
  O2Micro OZ6832/33 rev 02 PCI-to-CardBus at slot 00:0a, mem 0x68000000
    host opts [0]: [pc/pci] [pci irq 9] [lat 168/176] [bus 32/34]
    host opts [1]: [pc/pci] [pci irq 9] [lat 168/176] [bus 35/37]
    PCI irq 9 test failed
    ISA irqs (default) = 3,4,5,7,11 polling interval = 1000 ms
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x807
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x378-0x37f 0x388-0x38f 0x398-0x39f 0x4d0-0x4d7
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: cb_alloc(bus 32): vendor 0x10b8, device 0x0006
ROM image dump:
  image 0: 0x000000-0x000bff, signature PCIR
epic100.c:v1.07h 8/18/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/epic100.html
cs: cb_config(bus 32)
  fn 0 bar 1: io 0x1100-0x11ff
  fn 0 bar 2: mem 0x60041000-0x60041fff
  fn 1 bar 1: io 0x1000-0x10ff
  fn 1 bar 2: mem 0x60040000-0x60040fff
  fn 0 rom: mem 0x60030000-0x6003ffff
  fn 1 rom: mem 0x60020000-0x6002ffff
  irq 3
cs: cb_enable(bus 32)
  bridge io map 0 (flags 0x21): 0x1000-0x11ff
  bridge mem map 0 (flags 0x1): 0x60020000-0x60041fff
epic_attach(bus 32, function 0)
eth0: <NULL> at 0x1100, IRQ 3, 00:60:63:06:40:72.
eth0: MII transceiver #1 control 3100 status 7809.
eth0:  Autonegotiation advertising 01e1 link partner 0000.
serial_attach(device 20:00.1)
tty01 at 0x1000 (irq = 3) is a 16550A

Next-in-Thread Next Message

Select this message: To quick to be happy, seems to have some IRQ problem still

Messages Inline: 1 All Outline: 1 2 All

1. None Try some other irq_mode values by David Hinds, 2000, Aug 14
(_ None Tried irq_mode=3 and got it to stop complaining about IRQ9 but still not OK by Jan Calmered, 2000, Aug 16
(_ None Several issues by David Hinds, 2000, Aug 16
(_ Ok Ethernet working using 3.1.20 release, still some minor problems by Jan Calmered, 2000, Aug 17

Message Administration

This form allows you to delete, move, or copy one or more messages. You can move messages by copying and deleting the original. The action will be applied to the messages you select above and all replies to those selected messages.


If you want to copy or move messages, specify the HyperNews path of a destination forum or message that all messages will be copied or moved to. The destination must already exist, so maybe create it first.

Path of Destination (a Forum or Message): (e.g. "test")

Notify Subscribers at destination
NO


If you want to delete messages (the default), specify that here. If you want to move messages, you need to delete the original messages; placeholders will be left pointing to where they were moved.

Delete Messages
NO


Caution: After deleteing messages (the default), if you have not copied them (i.e. no destination above), then the selected messages are not be recoverable.

Members Subscribe No Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10
[ Edit This Forum ]