Next-in-Thread Next Message

Question DFE-650 only 10 Mbit? 

Forum: PCMCIA Network Adapter Issues
Date: 1999, Nov 29
From: tma

Hello, i have a rather strange problem with a D-LINK DFE-650 100TX card on an ACER Travelmate 332T.. the card itself works pretty good, but the maximum speed is ~ 1.18 mb/sec, which is exactly 10Mbit. the network/connection is about 6-8 mb/sec with win98 (spit!) using the same machine/card, so the problem seems to be the driver.. the faq lists this card as 10/100 & working, so i'm optimistic

dump of dmesg: (oh yes, and it's a somehow modified slackware 7.0)

Linux version 2.2.13 (root@flap) (gcc version 2.95.1 19990816 (release)) #2 Mon Nov 29 21:47:13 CET 1999
Detected 365819234 Hz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 365.36 BogoMIPS
Memory: 62908k/65472k available (1060k kernel code, 412k reserved, 1024k data, 68k init)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Mobile Pentium II stepping 0a
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xf0200
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5 
vesafb: framebuffer at 0x80800000, mapped to 0xc4000000, size 2560k
vesafb: mode is 800x600x8, linelength=800, pages=4
vesafb: protected mode interface info at c000:687c
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
Detected PS/2 Mouse Port.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS02 at 0x03e8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x0f (Driver version 1.9)
Real Time Clock Driver v1.09
Uniform Multi-Platform E-IDE driver Revision: 6.20
ALI15X3: IDE controller on PCI bus 00 dev 78
ALI15X3: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x7090-0x7097, BIOS settings: hda:DMA, hdb:pio
ALI15X3: simplex device:  DMA disabled
ide1: ALI15X3 Bus-Master DMA disabled (BIOS)
hda: IBM-DBCA-206480, ATA DISK drive
ide2: ports already in use, skipping probe
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ALI15X3: Ultra DMA enabled
hda: IBM-DBCA-206480, 6194MB w/420kB Cache, CHS=789/255/63, UDMA(33)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Partition check:
 hda: hda1 hda2 < hda5 hda6 > hda3
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 68k freed
Adding Swap: 104384k swap-space (priority -1)
parport0: PC-style at 0x378 [SPP,PS2,EPP]
lp0: using parport0 (polling).
CSLIP: code copyright 1989 Regents of the University of California
PPP: version 2.3.7 (demand dialling)
PPP line discipline registered.
PPP BSD Compression module registered
Linux PCMCIA Card Services 3.1.5
  kernel build: 2.2.13 #1 Mon Nov 29 21:17:51 CET 1999
  options:  [pci] [cardbus] [apm]
Intel PCIC probe: 
  O2Micro OZ6812 PCI-to-CardBus at bus 0 slot 19, mem 0x68000000, 1 socket
    host opts [0]: [a 24] [b 0d] [c 00] [d 83] [mhpg 18] [fifo 00] [e 2a] [no pci irq] [lat 32/176] [bus 32/34]
    ISA irqs (default) = 3,4,7,11,12 polling interval = 1000 ms
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:E0:98:73:A0:75
eth0: found link beat

thanks in advance, tma

Next-in-Thread Next Message

Select this message: DFE-650 only 10 Mbit?

Messages Inline: 1 All Outline: 1 2 All

1. None I don't really know by David Hinds, 1999, Nov 30
(_ Question right. by tma@ppmedia.at, 1999, Nov 30
(_ None Re: Question: right. by David Hinds, 1999, Nov 30

Message Administration

This form allows you to delete, move, or copy one or more messages. You can move messages by copying and deleting the original. The action will be applied to the messages you select above and all replies to those selected messages.


If you want to copy or move messages, specify the HyperNews path of a destination forum or message that all messages will be copied or moved to. The destination must already exist, so maybe create it first.

Path of Destination (a Forum or Message): (e.g. "test")

Notify Subscribers at destination
NO


If you want to delete messages (the default), specify that here. If you want to move messages, you need to delete the original messages; placeholders will be left pointing to where they were moved.

Delete Messages
NO


Caution: After deleteing messages (the default), if you have not copied them (i.e. no destination above), then the selected messages are not be recoverable.

Members Subscribe No Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10
[ Edit This Forum ]