Used both tulip_cb and epic

More: Used both tulip_cb and epic_cb

Forum: PCMCIA Network Adapter Issues
Re: Question: Argosy 10/100 EN-235 (Robert Rossmann)
Re: More: Argosy 10/100 more info (Robert Rossmann)
Re: Re: More: Argosy 10/100 more info (David Hinds)
Date: 2000, Feb 18
From: Robert Rossmann rbr

Entry in the config file

card "Argosy EN235 Fast Ethernet" manfid 0x10ec, 0x8138 bind "tulip_cb"

output in the message file
Feb 18 07:55:26 armin kernel: Linux PCMCIA Card Services 3.1.3 Feb 18 07:55:26 armin kernel: kernel build: 2.2.13 #1 Mon Nov 8 18:28:35 GMT 1999 Feb 18 07:55:26 armin kernel: options: [pci] [cardbus] [pnp] Feb 18 07:55:26 armin kernel: PnP: PNP BIOS installation structure at 0xc00ff000 Feb 18 07:55:26 armin kernel: PnP: PNP BIOS version 1.0, entry at e4000:a41, dseg at e4000 Feb 18 07:55:26 armin kernel: PCI routing table version 1.0 at 0xf2bb0 Feb 18 07:55:26 armin kernel: unknown PCI interrupt router 1045:c558 Feb 18 07:55:26 armin kernel: Intel PCIC probe: Feb 18 07:55:26 armin kernel: TI 1130 PCI-to-CardBus at bus 0 slot 7, mem 0x68000000, 2 sockets Feb 18 07:55:26 armin kernel: host opts [0]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 2/2] Feb 18 07:55:26 armin kernel: host opts [1]: [ring] [isa irq] [no pci irq] [lat 168/176] [bus 3/3] Feb 18 07:55:26 armin kernel: ISA irqs (scanned) = 7,9,10,11,12 status change on irq 11

The windows CardBus controller uses E/A 1400-14FF memory: 0x5042000-0x5423fff interrupt: 10
must or can I use this info for the Linux cardbus controller?
thx Robert

[ Next-in-Thread ] [ Next Message ]

Select this message: Used both tulip_cb and epic_cb

Messages Inline: [ 1 ] [ All ] Outline: [ 1 ] [ 2 ] [ All ]

1. More: More info by Robert Rossmann, 2000, Feb 21
(_ You are currently out of luck by David Hinds, 2000, Feb 21

Message Administration

This form allows you to delete, move, or copy one or more messages. You can move messages by copying and deleting the original. The action will be applied to the messages you select above and all replies to those selected messages.

If you want to copy or move messages, specify the HyperNews path of a destination forum or message that all messages will be copied or moved to. The destination must already exist, so maybe create it first.

Path of Destination (a Forum or Message): (e.g. "test")

Notify Subscribers at destination
NO

If you want to delete messages (the default), specify that here. If you want to move messages, you need to delete the original messages; placeholders will be left pointing to where they were moved.

Delete Messages
NO

Caution: After deleteing messages (the default), if you have not copied them (i.e. no destination above), then the selected messages are not be recoverable.

[ Members ] [ Subscribe ] [ No Admin Mode ]
[ Show Frames ] [ Help for HyperNews at pcmcia-cs.sourceforge.net 1.10 ]
[ Edit This Forum ]