Next-in-Thread Next Message

Feedback laplop manufactured in China. & my config files 

Forum: PCMCIA Network Adapter Issues
Re: Sad eth0:interrupt(s) dropped! (Ray)
Re: None So give us a hint: what brand and model of card is this? (David Hinds)
Date: 2000, Apr 01
From: Ray jxray

thanx for your quick reply!!

card "LN1078"
  manfid 0xffff, 0x1090
  bind "pcnet_cs"
module "pcnet_cs" opts "hw_addr=0x00,0x00,0x21,0x0e,0x--,0x--"
#dmesg    //after a /etc/rc.d/init.d/pcmcia restart & command "route" was executed
unloading PCMCIA Card Services
Linux PCMCIA Card Services 3.1.13
  kernel build: 2.2.12-20 #1 Mon Sep 27 10:40:35 EDT 1999
  options:  [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xfdf70
Intel PCIC probe: 
  TI 1225 PCI-to-CardBus at slot 00:04, mem 0x68000000
    host opts [0]: [ring] [serial pci & irq] [pci irq 11] [lat 64/176] [bus 32/34]
    host opts [1]: [ring] [serial pci & irq] [pci irq 11] [lat 64/176] [bus 35/37]
    PCI irq 11 seems to be wedged!
    PCI irq 11 test failed
    ISA irqs (default) = 3,4,5,7,9,10 polling interval = 1000 ms
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:00:21:0E:--:--  //sorry for hide this.
eth0: interrupt from stopped card
eth0: interrupt(s) dropped!
eth0: Reentering the interrupt handler! isr=0x0 imr=0x0.
eth0: Reentering the interrupt handler! isr=0x0 imr=0x0.

can these messages help?
i compiled & installed pcmcia-cs-3.1.13 using default options.

this poor card is called ln1078. 
Based on IEEE 802.30Base-T,IEEE 802.3u 100Base-TX
ioport 0x240-0x360
irq 2,3,4,5,10,11,12,15
data cache buffer 64k
it can work at 10M/100M duplex mode.
info can be get at but it is build in chinese language. :(

many laptop users in china use this card like me. diff is they use windoz i use linux. :)

Next-in-Thread Next Message

Select this message: laplop manufactured in China. & my config files

Messages Inline: 1 All Outline: 1 2 All

1. None I'm afraid you are out of luck for now by David Hinds, 2000, Apr 03
(_ Ok I'll be waiting for your new drivers...:) by Ray, 2000, Apr 04

Message Administration

This form allows you to delete, move, or copy one or more messages. You can move messages by copying and deleting the original. The action will be applied to the messages you select above and all replies to those selected messages.

If you want to copy or move messages, specify the HyperNews path of a destination forum or message that all messages will be copied or moved to. The destination must already exist, so maybe create it first.

Path of Destination (a Forum or Message): (e.g. "test")

Notify Subscribers at destination

If you want to delete messages (the default), specify that here. If you want to move messages, you need to delete the original messages; placeholders will be left pointing to where they were moved.

Delete Messages

Caution: After deleteing messages (the default), if you have not copied them (i.e. no destination above), then the selected messages are not be recoverable.

Members Subscribe No Admin Mode Show Frames Help for HyperNews at 1.10
[ Edit This Forum ]