I use a Thinkpad 385XD with an IBM 10/100 Etherjet Cardbus Adapter and an IBM International Modem with GSM PC Card. The installation is an SuSE 6.4 (Kernel 2.2.14 with APM Support) with cardctl 3.1.11. It looks all fine during bootup and card detecting, but any access to the LAN fail. I connected directly to our switch and the switch receive frames. The LEDs of the cableadapter blinks too. But there is no response to ping, traceroute, ... After adding "debug=255" to the tulip_cs module I get the following messages. /var/log/messages: Apr 18 13:43:12 laptop-tti kernel: Linux PCMCIA Card Services 3.1.11 Apr 18 13:43:12 laptop-tti kernel: kernel build: 2.2.14 #1 Sat Mar 25 00:46:59 GMT 2000 Apr 18 13:43:12 laptop-tti kernel: options: [pci] [cardbus] [apm] Apr 18 13:43:12 laptop-tti kernel: PCI routing table version 1.0 at 0xfb150 Apr 18 13:43:12 laptop-tti kernel: 00:02.0 -> irq 11 Apr 18 13:43:12 laptop-tti kernel: 00:02.1 -> irq 11 Apr 18 13:43:12 laptop-tti kernel: Intel PCIC probe: Apr 18 13:43:12 laptop-tti kernel: TI 1250A PCI-to-CardBus at slot 00:02, mem 0x50000000 Apr 18 13:43:12 laptop-tti kernel: host opts [0]: [ring] [isa irq] [pci irq 11] [lat 168/176] [bus 1/3] Apr 18 13:43:12 laptop-tti kernel: host opts [1]: [ring] [isa irq] [pci irq 11] [lat 168/176] [bus 4/6] Apr 18 13:43:12 laptop-tti kernel: ISA irqs (scanned) = 3,4,7,9,10,15 PCI status changes Apr 18 13:43:12 laptop-tti kernel: cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff Apr 18 13:43:12 laptop-tti kernel: cs: IO port probe 0x0800-0x08ff: clean. Apr 18 13:43:12 laptop-tti kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x220-0x22f 0x388-0x38f 0x3b8-0x3df 0x4d0-0x4d7 Apr 18 13:43:12 laptop-tti kernel: cs: cb_alloc(bus 4): vendor 0x115d, device 0x0003 Apr 18 13:43:12 laptop-tti kernel: ROM image dump: Apr 18 13:43:12 laptop-tti kernel: image 0: 0x000000-0xffffffff, signature PCIR Apr 18 13:43:12 laptop-tti kernel: cs: cb_config(bus 4) Apr 18 13:43:12 laptop-tti kernel: fn 0 bar 1: io 0x100-0x17f Apr 18 13:43:12 laptop-tti kernel: fn 0 bar 2: mem 0x6000d000-0x6000d7ff Apr 18 13:43:12 laptop-tti kernel: fn 0 bar 3: mem 0x6000c000-0x6000c7ff Apr 18 13:43:12 laptop-tti kernel: fn 0 rom: mem 0x60008000-0x6000bfff Apr 18 13:43:12 laptop-tti kernel: cs: cb_enable(bus 4) Apr 18 13:43:12 laptop-tti kernel: bridge io map 0 (flags 0x21): 0x100-0x17f Apr 18 13:43:12 laptop-tti kernel: bridge mem map 0 (flags 0x1): 0x60008000- 0x6000dfff Apr 18 13:43:12 laptop-tti kernel: tulip_reap() Apr 18 13:43:12 laptop-tti kernel: tulip_attach(bus 4, function 0) Apr 18 13:43:12 laptop-tti kernel: tulip.c:v0.91g-ppc 7/16/99 becker@cesdis.gsfc.nasa.gov (modified by danilo@cs.uni-magdeburg.de for XIRCOM CBE, fixed by Doug Ledford) Apr 18 13:43:12 laptop-tti kernel: eth0: Xircom Cardbus Adapter (DEC 21143 compatible mode) rev 3 at 0x100, 00:04:AC:90:DD:73, IRQ 11. Apr 18 13:43:12 laptop-tti kernel: eth0: MII transceiver #0 config 3100 status 7809 advertising 01e1. Apr 18 13:43:12 laptop-tti kernel: eth0: tulip_open() irq 11. Apr 18 13:43:12 laptop-tti kernel: eth0: interrupt csr5=0x60678006 new csr5=0x60660000. Apr 18 13:43:12 laptop-tti kernel: eth0: The transmitter stopped. CSR5 is 60678006, CSR6 324c2002, new CSR6 32400000. Apr 18 13:43:12 laptop-tti kernel: eth0: interrupt csr5=0x60670004 new csr5=0x60660000. Apr 18 13:43:12 laptop-tti kernel: eth0: interrupt csr5=0x60660000 new csr5=0x60660000. Apr 18 13:43:12 laptop-tti kernel: eth0: exiting interrupt, csr5=0x60660000. Apr 18 13:43:12 laptop-tti kernel: eth0: Done tulip_open(), CSR0 fea08000, CSR5 60660000 CSR6 324c2002. Apr 18 13:43:12 laptop-tti kernel: eth0: interrupt csr5=0x60670004 new csr5=0x60660000. ... /var/log/warn: Apr 18 13:43:12 laptop-tti kernel: eth0: The transmitter stopped. CSR5 is 60678006, CSR6 324c2002, new CSR6 32400000. can somebody help me? Thanks a lot Torsten |