Next-in-Thread Next Message

None Re: I think I need a bit more information 

Forum: PCMCIA Network Adapter Issues
Re: Question Genius MF3000 stalls 3.1.14 (Philip Martin)
Re: None I think I need a bit more information (David Hinds)
Date: 2000, Jun 06
From: Philip Martin philip

David Hinds <dhinds@valinux.com> writes:

> >  May 16 21:26:29 debian1 cardmgr[155]: initializing socket 0
> 
> What messages do you get before this?  (the Intel PCIC probe
> messages?)

 Jun  6 21:00:39 debian1 kernel: Linux PCMCIA Card Services 3.1.14
 Jun  6 21:00:39 debian1 kernel:   kernel build: 2.2.15 unknown
 Jun  6 21:00:39 debian1 kernel:   options:  [pci] [cardbus] [apm]
 Jun  6 21:00:39 debian1 kernel: PCI routing table version 1.0 at 0xfe840
 Jun  6 21:00:39 debian1 kernel:   00:08.0 -> irq 10
 Jun  6 21:00:39 debian1 kernel:   00:08.1 -> irq 10
 Jun  6 21:00:39 debian1 kernel:   01:00.0 -> irq 10
 Jun  6 21:00:39 debian1 kernel: Intel PCIC probe: 
 Jun  6 21:00:39 debian1 kernel:   TI 1225 rev 01 PCI-to-CardBus at slot 00:08, mem 0x68000000
 Jun  6 21:00:39 debian1 kernel:     host opts [0]: [pci + serial irq] [pci irq 10] [lat 168/176] [bus 32/0]
 Jun  6 21:00:39 debian1 kernel:     host opts [1]: [pci + serial irq] [pci irq 10] [lat 168/176] [bus 35/0]
 Jun  6 21:00:39 debian1 kernel:     ISA irqs (scanned) = 3,4,7,9,11 PCI status changes
 Jun  6 21:00:39 debian1 cardmgr[134]: starting, version is 3.1.14
 Jun  6 21:00:39 debian1 cardmgr[134]: watching 2 sockets
 Jun  6 21:00:39 debian1 kernel: cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
 Jun  6 21:00:39 debian1 kernel: cs: IO port probe 0x0800-0x08ff: clean.
 Jun  6 21:00:39 debian1 kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x398-0x39f 0x4d0-0x4d7
 Jun  6 21:00:39 debian1 kernel: cs: IO port probe 0x0a00-0x0aff: clean.
 Jun  6 21:00:40 debian1 kernel: cs: cb_alloc(bus 32): vendor 0x1011, device 0x0019
 Jun  6 21:00:40 debian1 cardmgr[134]: initializing socket 0
 Jun  6 21:00:40 debian1 kernel: ROM image dump:
 Jun  6 21:00:40 debian1 kernel:   image 0: 0x000000-0x0001ff, signature PCIR
 Jun  6 21:00:40 debian1 cardmgr[134]: socket 0: Tulip-based CardBus Fast Ethernet
 Jun  6 21:00:40 debian1 cardmgr[134]: executing: 'insmod /lib/modules/2.2.15/pcmcia/cb_enabler.o'
 Jun  6 21:00:40 debian1 cardmgr[134]: executing: 'insmod /lib/modules/2.2.15/pcmcia/tulip_cb.o debug=6'
 Jun  6 21:00:40 debian1 kernel: cs: cb_config(bus 32)
 Jun  6 21:00:40 debian1 kernel:   fn 0 bar 1: io 0x200-0x27f
 Jun  6 21:00:40 debian1 kernel:   fn 0 bar 2: mem 0x600c0000-0x600c03ff
 Jun  6 21:00:40 debian1 kernel:   fn 0 rom: mem 0x60080000-0x600bffff
 Jun  6 21:00:40 debian1 kernel: cs: cb_enable(bus 32)
 Jun  6 21:00:40 debian1 kernel:   bridge io map 0 (flags 0x21): 0x200-0x27f
 Jun  6 21:00:40 debian1 kernel:   bridge mem map 0 (flags 0x1): 0x60080000-0x600c0fff
 Jun  6 21:00:40 debian1 kernel: tulip_reap()
 Jun  6 21:00:40 debian1 kernel: tulip_attach(bus 32, function 0)
 Jun  6 21:00:40 debian1 kernel: tulip.c:v0.91g-ppc 7/16/99 becker@cesdis.gsfc.nasa.gov (modified by danilo@cs.uni-magdeburg.de for XIRCOM CBE, fixed by Doug Ledford)
 Jun  6 21:00:40 debian1 kernel: eth0: Digital DS21143 Tulip rev 65 at 0x200, 00:A0:0C:90:6D:9A, IRQ 10.
 Jun  6 21:00:40 debian1 kernel: eth0:  EEPROM default media type Autosense.
 Jun  6 21:00:40 debian1 kernel: eth0:  Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2) block.
 Jun  6 21:00:40 debian1 kernel: eth0:  Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY (2) block.
 Jun  6 21:00:40 debian1 kernel: eth0:  Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4) block.
 Jun  6 21:00:40 debian1 kernel: eth0:  Index #3 - Media 100baseTx-FD (#5) described by a 21143 SYM PHY (4) block.
 Jun  6 21:00:40 debian1 kernel: eth0: Restarting 21143 autonegotiation, 0003ffff.
 Jun  6 21:00:40 debian1 cardmgr[134]: executing: './network start eth0'
 Jun  6 21:00:40 debian1 kernel: eth0: tulip_open() irq 10.
 Jun  6 21:00:40 debian1 kernel: eth0: Restarting 21143 autonegotiation, 0003ffff.
 Jun  6 21:00:40 debian1 kernel: eth0: Done tulip_open(), CSR0 f8a08000, CSR5 f0320000 CSR6 b2422202.
 Jun  6 21:00:40 debian1 kernel: eth0: interrupt  csr5=0xf0670004 new csr5=0xf0660000.
 Jun  6 21:00:40 debian1 kernel: eth0: interrupt  csr5=0xf0660000 new csr5=0xf0660000.
 Jun  6 21:00:40 debian1 kernel: eth0: exiting interrupt, csr5=0xf0660000.

> And what sort of laptop is this?

I don't know who really manufactures it. I bought it from Rock
Computers in the UK, its their Sigma model. Its about 9 months old, it
has a 433MHz Celeron processor, a BX chipset, and a SystemSoft Mobile
Pro BIOS.

For what it's worth the User Manual (which I've just read for the
first time) claims: "PC Card Slots: Compliant with PCMCIA 2.1/JEIDA
4.1 specifications along with ExCA extension and PC CARD standard, two
PC card slots for two type II application, supporting CardBus and
Zoomed Video port".

> 
> > I also have a 3Com 3CCFEM556B which works fine, so the problem would
> > appear to lie with the tulip driver.
> 
> Not necessarily; it could be in the code that configures the CardBus
> bridge.

Next-in-Thread Next Message

Add Message to: "Re: I think I need a bit more information"

Members Subscribe Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10