• Resolving installation and configuration problems
• PCMCIA serial and modem devices

Messages Inline: [ 0 ]  [ All ]  Outline: [ 1 ]  [ 2 ]  [ All ] 

Question: wrong UART detected Date: 1999, Nov 04 From: Jaime V Miro jaime

Hi there, Is there any way to force the driver to use a particular UART? I have a "Socket" pcmcia serial card (not multi), which is properly identified with "cardctl ident", but the UART is wrongly detected as 8250 instead of 16550. This is happening in kernel 2.0.36 and also in 2.2.9 (Red Hat systems) and with the same results in the following pcmcia packages: 3.0.12, 3.0.13, 3.0.14, and 3.1.3 I am currently downloading kernel 2.2.13 to see if the problem is sorted, but somehow I don't expect it to happen. I am confident the serial card UART uses 16550 because I had it running under 2.0.36 and pcmcia-cs-3.0.12 (although not always, sometimes it would also detect a 8250, and after a cold reboot it would then recognise 16550). However, I updated to 2.2.9 and pcmcia-cs-3.1.3 to get my pcmcia network card to work (3COM 3c575), as recomended by D. Hinds. Network card is now working, but I have not been able to recognise the 16550 UART with all possible combinations of the above kernels and pcmcia packages. Any recommendations? Thanks in advance, Jaime

1. Is this the real problem? by David Hinds, 1999, Nov 04

Question: Multitech MT5634ZLX modem problems Date: 1999, Nov 05 From: Ray Muno munorc

We are trying to use a Multitech MT5634ZLX PCMCIA modem on a Dell Inspiron 3500. The card is recognized as a serial device and installed but we cannot talk to the modem at all. Is anyone using this device? BTW, the modem operates fine under Windows 98. The device is not a Winmodem. We are running Debian 2.1, Card Services 3.0.14, 2.2.7 kernel. I have no problems running other PCMCIA cards, Ethernet and even CardBus Fast Ethernet.

1. What have you tried, exactly? by David Hinds, 1999, Nov 05

Question: O2Micro OZ6836/OZ6860 PCI-to-CardBus Date: 1999, Nov 18 From: Michael Larsen larsenm

Problem: ------------ Hard boot of an old kernel required to get PCMCIA Card Services working with a new kernel. Description: ------------- I have EPS Tech. MP-979 Laptop with an O2Micro OZ6836/OZ6860 CardBus controller and a 56K modem card (Lucent Tech. Venus I think?). The BIOS setting for pnp is yes. I recently upgraded my 2.0.35 kernel to 2.2.13-7mdk. The 56K modem card was working with PCMCIA Card Services version 3.0.4 compiled into the kernel. To get the card detected in the 2.0.35 kernel, I had to include memory 0xd8000-0xdffff in /etc/pcmcia/config.opts. For the new kernel, as suggested by the PCMCIA-HOWTO, I added include memory 0xa0000000-0xa0ffffff to /etc/pcmcia/config.opts. My problem is that the new kernel fails to load the PCMCIA modules (based on Card Services 3.1) and generates an oops: Linux PCMCIA Card Services 3.1.0 kernel build: 2.2.13-7mdk #1 Wed Sep 15 18:02:18 CEST 1999 options: [pci] [cardbus] [apm] [pnp] PnP: PNP BIOS installation structure at 0x800f6270 PnP: PNP BIOS version 1.0, entry at f0000:a4e3, dseg at 400 PCI routing table version 1.0 at 0xfdf80 00:08.2 -> irq 0 00:03.0 -> irq 0 00:03.1 -> irq 0 Intel PCIC probe: <6>base 68000000: ff ff ff ff base f8000000: ff ff ff ff Bridge register mapping failed: check cb_mem_base setting Unable to handle kernel paging request at virtual address 84834800 current->tss.cr3 = 026d5000, %cr3 = 026d5000 *pde = 03c80063 *pte = 00000000 Oops: 0000 CPU: 0 EIP: 0010:[<8482d847>] I tracked this done to the idnetify routine of the i82365.o module. If however, I hard boot the old 2.0.35 kernel first, and then warm reboot the new kernel, the modules load and the card is recognized. (Further warm reboots of the new kernel result in modules loading correctly and the card being recognized: Linux PCMCIA Card Services 3.1.0 kernel build: 2.2.13-7mdk #1 Wed Sep 15 18:02:18 CEST 1999 options: [pci] [cardbus] [apm] [pnp] PnP: PNP BIOS installation structure at 0x800f6270 PnP: PNP BIOS version 1.0, entry at f0000:a4e3, dseg at 400 PCI routing table version 1.0 at 0xfdf80 00:08.2 -> irq 0 00:03.0 -> irq 0 00:03.1 -> irq 0 Intel PCIC probe: O2Micro OZ6836/OZ6860 PCI-to-CardBus at bus 0 slot 3, mem 0x68000000, 2 sockets host opts [0]: [a 44] [b 81] [c 00] [d 83] [mhpg 18] [fifo 08] [e 0a] [no pci irq] [lat 168/176] [bus 32/34] host opts [1]: [a 44] [b 8d] [c 50] [d 83] [mhpg 18] [fifo 08] [e 0a] [no pci irq] [lat 168/176] [bus 35/37] ISA irqs (default) = 3,4,5,7,9,10,11,12 polling interval = 1000 ms cs: IO port probe 0x0100-0x03ff: excluding 0x200-0x207 cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa00fffff tty02 at 0x03e8 (irq = 3) is a 16550A Any suggestions on how to get things working without a hard reboot of the old kernel? /etc/sysconfig/pcmcia: PCMCIA=yes PCIC=i82365 CORE_OPTS= CARDMGR_OPTS= /etc/pcmcia/config.opts include port 0x100-0x3ff include memory 0xd8000-0xdffff include memory 0xa0000000-0xa0ffffff include memory 0x44000000-0x44001fff include memory 0x48000000-0x48ffffff exclude irq 4 Some things I tried: -------------------- I get similar pattern with kernel 2.3.24 and PCMCIA Card Services version 3.1.4. Instead of an oops it generates a loop beep+high beep. The modules load, but the card is detected as anonymous memory. I tried restarting cardmgr with a few different memory ranges in config.opts without success. Thanks in advance, --- Michael

1. I think this has already been fixed by David Hinds, 1999, Nov 23

Question: Request IO: No more items Date: 1999, Nov 30 From: Brian Mays brian

I am trying to help someone who is having problems with his PCMCIA modem. He is using version 3.1.4, and when inserting his modem, he gets the message: serial_cs: RequestIO: No more items and the module is not loaded. The card used to work with a previous version of PC Card Services. Any help would be appreciated. Thanks. Brian

1. More info? by David Hinds, 1999, Dec 02

Question: OPTION GSM card under Linux Date: 1999, Dec 06 From: Bernhard Graf bgraf

I have bought an OPTION GSM-only PCMCIA card and am trying to get it to work under Linux, Kernel 2.2.5 (SuSE 6.1), PCMCIA driver 3.1.5. It is recognized by cardmgr and cardinfo displays it as a serial or modem card. Cardctl displays it as : Socket 1: product info: "Option International", "GSM Data/Fax/SMS Modem", "V1.300", "" manfid: 0x0013, 0x0000 function: 2 (serial) But unfortunately, it seems not to work ! When I start minicom and try to connect to /dev/ttyS1, which is what the serial start command displays as the port, the modem does not answer to AT commands. Question : Is this one of the kinds of modems that tell they are one but in reality need a (Windows) driver to function like one ? Or is it just a configuration issue ? Please help ! Bernhard Graf

1. Ok: OPTION GSM card works fine now ! by Bernhard Graf, 1999, Dec 08

Question: Quatech quad serial card Date: 1999, Dec 09 From: Jeff jas

Hey, I bough a Quatech quad serial card after seeing it was on the supported card list. Does anyone know where I could possibly find some documentation about making the serial devices and getting the card to work properly? cardctl -ident finds and identifies the card just fine, only I don't know what to do after that. Thanks in advanced. Jeff

1. Check your system log by David Hinds, 1999, Dec 09

Nokia Cardphone anyone Date: 1999, Dec 13 From: Madsen Wikholm madsen

Has anybody tested the Nokia Cardphone 2.0. I'm in the need of mobile computing and a friend suggested I'd get this card. The question is: does it work under Linux? I'm actually not sure if this card exists yet...but it seems like it. best regards, madsen

Question: MC221 COM One Date: 1999, Dec 15 From: Tobi Oetiker tobi

I just got a Vaio N505x ... It comes with a COM One Platinium Modem CardBus Card MC221. When I insert this card it does not get recoginzed by the PCMCIA module. "No product info available". On the PCI bus howver (/proc/pci) it does show up as ---------------- Bus 32, device 0, function 0: Communication controller: Lucent Mocroelectronics L56xMF (rev 1). Medium devsel. Fast back-to-back capable ---------------- Now I guss the problem is that this thing is a soft modem. But then again it might work with this new Driver just published by lucent ... any info on this? tobi

1. Well then, just try it... by David Hinds, 1999, Dec 16 (_ Question: Lucent = wavelan? by Armin Obersteiner, 2000, Jan 18 (_ Sorry... by David Hinds, 2000, Jan 18

Sad: register_serial(): autoconfig failed (Inet Spider II card -- 16550 CDPD modem) Date: 1999, Dec 24 From: Scott Petrack scott.petrack

Dell Inspiron 7000, RedHat 6.1, kernel-pcmcia-cs-2.2.12-20 I regularly use a generic Viking modem card and Xircom RealPort CardBus 10/100 card. Just got an Inet Spider II CDPD modem card, which seems either to be (or maybe just emulate) a generic 16550 modem card. Under Windows the card works fine with the generic serial/modem drivers, using SLIP and dial-up networking, so I am full of hope that I can get it to work under Linux as well. But when I insert the card, I get the following failure (and the high-beep/low-beep sounds): [scott]# tail /var/log/messages Dec 24 06:34:15 scott cardmgr[900]: initializing socket 1 Dec 24 06:34:15 scott cardmgr[900]: socket 1: Serial or Modem Dec 24 06:34:15 scott cardmgr[900]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/serial_cs.o' Dec 24 06:34:15 scott kernel: register_serial(): autoconfig failed Dec 24 06:34:15 scott kernel: serial_cs: register_serial() at 0x02f8, irq 3 failed Dec 24 06:34:16 scott cardmgr[900]: get dev info on socket 1 failed: Resource temporarily unavailable [scott]# dump_cis Socket 0: no CIS present Socket 1: dev_info NULL 0ns, 512b vers_1 5.0, "Nextcell", "Spider II Wireless IP Modem", "V1.1" manfid 0x01e1, 0x0100 funcid serial_port config base 0x0200 mask 0x001f last_index 0x05 cftable_entry 0x01 [default] [rdybsy] [pwrdown] Vcc Vnom 5V Istatic 200mA Iavg 400mA Ipeak 500mA Idown 20mA io 0x02f8-0x02ff [lines=0] [8bit] [range] irq mask 0xfffc [level] cftable_entry 0x03 io 0x03e8-0x03ef [lines=0] [8bit] [range] cftable_entry 0x05 io 0x02e8-0x02ef [lines=0] [8bit] [range] The HOWTOs suggest an interrupt or port conflict, but there seems to be no interrupt nor io port conflict. As proof, I ejected the Spider card and then inserted my modem PCMCIA card. It works fine: two high beeps and here is the successful output: [scott]# tail /var/log/messages Dec 24 06:33:55 scott cardmgr[900]: initializing socket 1 Dec 24 06:33:55 scott cardmgr[900]: socket 1: Serial or Modem Dec 24 06:33:55 scott cardmgr[900]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/serial_cs.o' Dec 24 06:33:55 scott kernel: tty01 at 0x02f8 (irq = 3) is a 16550A Dec 24 06:33:55 scott cardmgr[900]: executing: './serial start ttyS1' [scott]#dump_cis Socket 0: no CIS present Socket 1: dev_info no_info vers_1 4.1, "Viking", "V.90 K56flex", "021", "A" manfid 0x0013, 0x0000 funcid serial_port config base 0x0200 mask 0x0017 last_index 0x30 cftable_entry 0x20 [default] [rdybsy] [audio] [pwrdown] Vcc Istatic 25mA Iavg 250mA Ipeak 300mA Idown 5mA timing ready 500ms io 0x03f8-0x03ff [lines=10] [8bit] [range] irq mask 0x86bc [level] cftable_entry 0x21 io 0x02f8-0x02ff [lines=10] [8bit] [range] cftable_entry 0x22 io 0x03e8-0x03ef [lines=10] [8bit] [range] cftable_entry 0x23 io 0x02e8-0x02ef [lines=10] [8bit] [range] cftable_entry 0x30 io 0x0000-0x0007 [lines=3] [8bit] As a final note about the Spider card, I did call Spider technical support before I bought the card and I was told that the card really does act like an generic serial port card to the computer. The page http://www.nextcell.com/solution/s2specs.html mentions that the card does "16650 emulation". From what I can see on the Windows side, there is not a single new driver installed, so it really does use the generic serial pcmcia drivers under Windows. I know that the next step is to compile sources to serial_cs, or kernel_pcmcia_cs, but I was hoping that before I start mucking about with sources that you might be able to help me. Thanks very much indeed. Happy holiday if you're into that sort of thing, Scott

1. Note: Oops, forgot cardctl -V and uname -rv by Scott Petrack, 1999, Dec 24 (_ More: compiled kernel-cs with pc_debug: "odd IO request" by Scott Petrack, 1999, Dec 27 1. More: Could the problem be with the "lines=0" in the dump_cis output? by Scott Petrack, 1999, Dec 27 2. Re: More: compiled kernel-cs with pc_debug: "odd IO request" by David Hinds, 1999, Dec 27 1. More: Point me in the right direction please? by Scott Petrack, 1999, Dec 27 ... 2 Message(s)

Question: modem doesn't work until setserial irq 0 -- but works after Date: 1999, Dec 29 From: John Ruttenberg rutt

System brand & model: gateway solo 9100xl PCMCIA card: telepath 56k modem Linux version: 2.2.13 Pcmcia version: 3.1.7 (+cardbus +PnP) This modem doesn't work at all until I do: setserial /dev/modem irq 0 But the strange thing is that once this has been done once, the modem will aways work even after: setserial /dev/modem irq 11 (11 is the irq assigned by pcmcia in the first place.) In fact, the modem will even work after stopping and restarting pcmcia with: /etc/rc.d/init.d/pcmcia stop /etc/rc.d/init.d/pcmcia start But after a reboot, the modem won't work until the irq has once been set to 0. By the way, I have: PCIC_OPTS="pci_csc=1"

1. Kernel bug, workaround in 3.1.10 by David Hinds, 2000, Feb 04

Question: modem dead? Date: 2000, Jan 03 From: Richard Sevenich rsevenic

I have a laptop whose modem has stopped working and I know not whether it is a software or hardware problem - being relatively unfamiliar with pcmcia. Symptoms: 1. When card services start, the card is successfully identified. 2. cardctl status indicates on the 2nd line function 0: [ready], [bat low], [bat dead] (the latter two flags make me nervous) 3. At start, /dev/modem is created as a soft link to /dev/ttyS1, but I cannot examine /dev/modem with setserial - the attempt hangs the system 4. The card is a PCMCIA MAKER, 56K V.90 DataFax Modem I would appreciate help/hints. Regards, Richard

1. Hard to tell without more testing by David Hinds, 2000, Jan 03

Sad: Modem of Xircom multifunction stalls at reproducible point Date: 2000, Jan 13 From: Jon Sundquist <jsundqui@buffnet.net>

The ethernet part of my Xircom REM56G-10BT (it is the 16-bit realport card, combo 10BT ether and 56K modem) works great as an ethernet card. It also works in modem mode, but with troubles. I can reproducibly stall a file transfer. Setup: Dell Inspiron 3500 Redhat 6.1, with pcmcia upgraded to 3.1.8 (upgrade didn't help) Card: Xircom REM56G-10BT inspiron:~$ uname -rv 2.2.12-20 #1 Mon Sep 27 10:40:35 EDT 1999 inspiron:~$ /sbin/cardctl -V cardctl version 3.1.8 More details of problem: I use kppp to initiate a modem ppp connection (a usenet post said that kppp may be a culprit, but that seems unlikely, and I have not yet crafted a straight pppd/chat script to confirm). Connection is made OK (sometimes not at too great a speed, but I chalk that up to poor lines). Things like web surfing are fine. Now go to this page: http://www.vmware.com/download/downloadtools.html and try to download the vmware-tools package from any of the mirrors there. It always, reproducibly stalls at 5% (at about 77000 - 78000 bytes). It will stall from any of the mirrors, both from ftp and http. Interestingly, although it stalls the same place each time, some packets still come through. I.e., it transfers fine till about 5%, then maybe a packet or two every minute, but gradually getting even slower. I mainly use the ethernet, so I havaen't done extensive testing for different sites/limitations. However, there were other downloads where I had similar problems (e.g. a TkDesk rpm from RedHat contrib IIRC). However, I have also had some downloads with no problems. Again, loading web pages seems unaffected. I had some problems (long delays) loading/refreshing an IMAP mailbox, but that has not been quite so reproducible. This is a dual boot machine. I had no problem downloading these files in windows via modem. When swicthing between ethernet and modem, I first bring down the eth0 interface (ifconfig down) along with the associated routes. Script changes: none serial-related. I added the network.opts as recommended for redhat. I also used redhats /etc/pcmcia/network. But then again, I am not having problems with the network, but with the modem/serial. From the logs: This is from /var/log/messages from after I restarted cardmgr (via /etc/rc.d/init.d/pcmcia stop|start) following the installation of 3.1.8. Note, I first tested ethernet to see if it worked, then brought that down, and ran the ppp session. Jan 12 18:16:36 inspiron cardmgr[6631]: starting, version is 3.1.8 Jan 12 18:16:36 inspiron cardmgr[6631]: watching 2 sockets Jan 12 18:16:36 inspiron cardmgr[6631]: initializing socket 0 Jan 12 18:16:36 inspiron cardmgr[6631]: socket 0: Xircom RealPort REM10BT Ethernet/Modem Jan 12 18:16:36 inspiron cardmgr[6631]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/xirc2ps_cs.o' Jan 12 18:16:36 inspiron cardmgr[6631]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/serial_cs.o' Jan 12 18:16:41 inspiron cardmgr[6631]: executing: './network start eth0' Jan 12 18:16:45 inspiron cardmgr[6631]: executing: './serial start ttyS3' Jan 12 18:21:50 inspiron modprobe: can't locate module char-major-108 Jan 12 18:21:50 inspiron pppd[6744]: pppd 2.3.10 started by root, uid 0 Jan 12 18:21:50 inspiron pppd[6744]: Using interface ppp0 Jan 12 18:21:50 inspiron pppd[6744]: Connect: ppp0 <--> /dev/ttyS3 Jan 12 18:21:56 inspiron pppd[6744]: Remote message: Login Succeeded Jan 12 18:21:57 inspiron pppd[6744]: local IP address 208.28.191.14 Jan 12 18:21:57 inspiron pppd[6744]: remote IP address 208.28.191.2 Jan 12 18:22:27 inspiron pppd[6744]: CCP: timeout sending Config-Requests Jan 12 18:28:51 inspiron pppd[6744]: Terminating on signal 15. Jan 12 18:28:51 inspiron pppd[6744]: Connection terminated. Jan 12 18:28:51 inspiron pppd[6744]: Connect time 7.1 minutes. Jan 12 18:28:51 inspiron pppd[6744]: Sent 21300 bytes, received 480012 bytes. Jan 12 18:28:51 inspiron pppd[6744]: Exit. I will post this at the Xircom area as well, although not sure if that is for the network "half" of it only. TIA for any suggestions

Sad: Modem doesn't work with versions 3.1.4 or later. Date: 2000, Jan 14 From: Dave Caswell davec

I can't get my PCMCIA serial port to work with versions of pcmcia-cs 3.1.4 and beyond. I haven't changed any configuration options, I just install the new versions over the old, and 3.1.4 on don't work. When I start pppd, syslog gets an error: Jan 13 16:24:01 krypton pppd[15407]: tcgetattr: Input/output error(5) and pppd exits. Looking back in my logs, I see that sometimes tty01 gets ports at 0x13f8, and sometimes at 0x02f8. But the card works at both addresses with the earlier versions of pcmcia_cs. My computer started life as a Debian distribution, but is now running kernel 2.1.14. The computer itself is a Toshiba Satellite Pro 445 CDX. Linux krypton 2.2.14 #2 Wed Jan 5 14:48:34 MST 2000 i586 unknown Socket 0: ActionTek Datalink Modem: product info: "PCMCIA ", "33.6K Fax/Modem ", "FM336LK " manfid: 0x0175, 0x0000 function: 2 (serial) Socket 1: product info: "SMC", "EtherEZ Ethernet 8020", "V1.00", "" manfid: 0x0108, 0x0001 function: 6 (network) The log file lines that relate to PCMCIA are: Jan 13 16:23:56 krypton kernel: Linux PCMCIA Card Services 3.1.4 Jan 13 16:23:56 krypton kernel: kernel build: 2.2.14 #2 Wed Jan 5 14:48:34 MST 2000 Jan 13 16:23:56 krypton kernel: options: [pci] [cardbus] [pnp] Jan 13 16:23:56 krypton kernel: PnP: PNP BIOS installation structure at 0xc00f8e30 Jan 13 16:23:56 krypton kernel: PnP: PNP BIOS version 1.0, entry at f0000:9c9d, dseg at 0 Jan 13 16:23:56 krypton kernel: PCI routing table version 1.0 at 0xf97e0 Jan 13 16:23:56 krypton kernel: Intel PCIC probe: Jan 13 16:23:56 krypton kernel: Intel i82365sl B step ISA-to-PCMCIA at port 0x3e0 ofs 0x00, 2 sockets Jan 13 16:23:56 krypton kernel: host opts [0]: none Jan 13 16:23:56 krypton kernel: host opts [1]: none Jan 13 16:23:56 krypton kernel: ISA irqs (scanned) = 3,4,10 polling interval = 1000 ms Jan 13 16:23:56 krypton cardmgr[15388]: starting, version is 3.1.4 Jan 13 16:23:56 krypton cardmgr[15388]: watching 2 sockets Jan 13 16:23:56 krypton kernel: cs: IO port probe 0x1000-0x17ff: clean. Jan 13 16:23:56 krypton kernel: cs: IO port probe 0x0100-0x04ff: clean. Jan 13 16:23:56 krypton kernel: cs: IO port probe 0x0a00-0x0aff: clean. Jan 13 16:23:57 krypton cardmgr[15388]: initializing socket 0 Jan 13 16:23:57 krypton kernel: cs: memory probe 0x0d0000-0x0dffff: clean. Jan 13 16:23:57 krypton cardmgr[15388]: socket 0: Serial or Modem Jan 13 16:23:57 krypton cardmgr[15388]: executing: 'insmod /lib/modules/2.2.14/pcmcia/serial_cs.o' Jan 13 16:23:57 krypton kernel: tty01 at 0x13f8 (irq = 3) is a 16550A Jan 13 16:23:57 krypton cardmgr[15388]: executing: './serial start ttyS1' Jan 13 16:24:01 krypton pppd[15407]: pppd 2.3.5 started by davec, uid 1000 Jan 13 16:24:01 krypton pppd[15407]: tcgetattr: Input/output error(5) Jan 13 16:24:02 krypton pppd[15407]: Exit. Jan 13 16:24:41 krypton cardmgr[15388]: executing: './serial check ttyS1' Jan 13 16:24:42 krypton cardmgr[15388]: shutting down socket 0 Jan 13 16:24:42 krypton cardmgr[15388]: executing: './serial stop ttyS1' Jan 13 16:24:42 krypton kernel: tty01 unloaded Jan 13 16:24:42 krypton cardmgr[15388]: executing: 'rmmod serial_cs' Jan 13 16:24:42 krypton cardmgr[15388]: exiting Thanks for your help. -davec

1. Ok: change in config.opts makes modem work again by Dave Caswell, 2000, Jan 15

Question: serial_cs device not found & null pointer Date: 2000, Jan 18 From: Mario Rossi ArmyBot

I'm having problem trying to install a PCMCIA modem...(linux, slackware 7.0) etc/pcmcia/config reflects what HOWTOs says device "serial_cs" class "serial" module "misc/serial", "serial_cs" I specified the manfid got with cardctl status, NO way I even tried specifying "serial_cs" as module ( 'cause there's serial_cs.o in pcmcia where is supposed to stay the file if no path is specified) NO WAY stab says socket 1 is empty ( not true) I'll add the whole boot log I got a null pointer probiung the second socket ( the modem ) , in fact the eth0 works fine but if you do cardctl status you see : Socket 0: 5V 16-bit card present Function 0: ready Socket 1: Socket 0: 5V 16-bit card present Function 0: ready,write protect <--- ???? Also it seems not to find the module serial_cs ( the same for serial) Could you help me ? Thanks a lot ArmyBot Linux version 2.2.13 (root@RsQgC) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #4 Tue Jan 18 18:29:37 CET 2000 Detected 119993660 Hz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 47.82 BogoMIPS Memory: 62996k/65536k available (1112k kernel code, 412k reserved, 956k data, 60k init) CPU: Intel Pentium 75 - 200 stepping 0c Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. Intel Pentium with F0 0F bug - workaround enabled. POSIX conformance testing by UNIFIX PCI: PCI BIOS revision 2.10 entry at 0xf7019 PCI: Using configuration type 1 PCI: Probing PCI hardware Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP Initializing RT netlink socket Starting kswapd v 1.5 Detected PS/2 Mouse Port. Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A pty: 512 Unix98 ptys configured apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9) Real Time Clock Driver v1.09 RAM disk driver initialized: 16 RAM disks of 4096K size loop: registered device at major 7 PCI_IDE: unknown IDE controller on PCI bus 00 device 11, VID=10b9, DID=5219 PCI_IDE: not 100% native mode: will probe irqs later PCI_IDE: simplex device: DMA disabled ide0: PCI_IDE Bus-Master DMA disabled (BIOS) PCI_IDE: simplex device: DMA disabled ide1: PCI_IDE Bus-Master DMA disabled (BIOS) hda: HITACHI_DK223A-81, ATA DISK drive hdc: UJDCD8730, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: HITACHI_DK223A-81, 775MB w/128kB Cache, CHS=787/32/63 hdc: ATAPI 8X CD-ROM drive, 128kB Cache Uniform CDROM driver Revision: 2.56 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8 linear personality registered raid0 personality registered Partition check: hda: hda1 hda2 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 60k freed Adding Swap: 45356k swap-space (priority -1) parport0: PC-style at 0x378 [SPP] lp0: using parport0 (polling). CSLIP: code copyright 1989 Regents of the University of California SLIP: version 0.8.4-NET3.019-NEWTTY-MODULAR (dynamic channels, max=256). SLIP linefill/keepalive option. PPP: version 2.3.7 (demand dialling) PPP line discipline registered. PPP BSD Compression module registered Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996 SB 3.01 detected OK (220) ESS chip ES1688 detected Linux PCMCIA Card Services 3.0.14 kernel build: 2.2.13 #22 Wed Oct 20 17:32:52 CDT 1999 options: [pci] [cardbus] Intel PCIC probe: TI 1130 PCI-to-CardBus at bus 0 slot 4, mem 0x68000000, 2 sockets host opts [0]: [isa irq] [no pci irq] [lat 64/176] [bus 1/5] host opts [1]: [isa irq] [no pci irq] [lat 64/176] [bus 6/10] ISA irqs (scanned) = 7,9,10,11,12 polling interval = 1000 ms cs: IO port probe 0x1000-0x17ff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x178-0x17f 0x388-0x38f 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. eth0: NE2000 Compatible: io 0x320, irq 9, hw_addr 00:80:C8:87:E5:2C Unable to handle kernel NULL pointer dereference at virtual address 00000004 current->tss.cr3 = 03d39000, %cr3 = 03d39000 *pde = 00000000 Oops: 0000 CPU: 0 EIP: 0010:[<c484dda8>] EFLAGS: 00010246 eax: 00000000 ebx: c0071280 ecx: c3c897e0 edx: 00000000 esi: 00000000 edi: c3d7b800 ebp: c3c7dad8 esp: c3c7dad0 ds: 0018 es: 0018 ss: 0018 Process cardmgr (pid: 72, process nr: 9, stackpage=c3c7d000) Stack: c3c897e0 c3d7b800 c3c7daec c484e6f3 c3c897e0 00000000 00000000 c3c7db6c c486f2e9 0000002d c3c897e0 00000000 c3c89900 00000000 c486f6e0 4d000000 c486f6e0 c3c7db00 00000000 00000032 00000032 00000032 49434d43 41432041 Call Trace: [<c484e6f3>] [<c486f2e9>] [<c486f6e0>] [<c486f6e0>] [<c01acd1b>] [<c486f4ee>] [<c486f450>] [<c484d589>] [<c4857135>] [<c485b9a6>] [<c486d082>] [<c484e8f5>] [<c484e693>] [<c486f14e>] [<c486f6e4>] [<c486f450>] [<c484f8a8>] [<c486f056>] [<c48625f3>] [<c01c1d89>] [<c4862f89>] [<c01b45af>] [<c01b5ccf>] [<c01b705e>] [<c01b82e3>] [<c01bc8e1>] [<c01bbe63>] [<c01bc053>] [<c011c8ff>] [<c011ca2b>] [<c011c2ef>] [<c011c5a1>] [<c012dc45>] [<c0109ef0>] Code: 8b 56 04 f6 c2 05 75 0d 66 83 7e 0a 00 74 0d f6 46 0c 05 74 ISO 9660 Extensions: RRIP_1991A

Question: MultiTech MT5634ZLX Date: 2000, Jan 19 From: Aaron Kaplan kaplan

I can't get my MultiTech MT5634ZLX modem to work. The card is recognized and assigned an appropriate IRQ and I/O port, but when I try to talk to it using minicom, nothing happens. I'm quite sure this is not a winmodem--the Windows disk that came with it contains only a .INF file and a DOS point enabler, no special driver. I'm using a Toshiba Satellite Pro 490XCDT, running RedHat 6.1. I tried first with the pcmcia package that was included in the distribution (3.0.14), and then upgraded to the latest 3.1.9, to no avail. This modem works fine under Windows. I have another modem card, a 14.4 from Fujitsu, that works just fine under Linux, in the same slot and using the same IRQ and port. MultiTech tech support won't help me. -Aaron

1. Interrupt conflict? by David Hinds, 2000, Jan 19 1. Re: Interrupt conflict? by Aaron Kaplan, 2000, Jan 20 (_ Uh-oh by David Hinds, 2000, Jan 20 2. Ok: A fix will be in the next 3.1.9 beta by David Hinds, 2000, Jan 25

Sad: Sierra Wireless Modem Date: 2000, Jan 25 From: Roy Murphy Royster

I just upgraded my system from RedHat 5.2 to Mandrake 7.0 and my Sierra Wireless Modem/Cell Modem card has stopped working. I applied Jeff Schoby's patches for the aircard to a version 3.1.9 PCMCIA source and recompiled/reinstalled. I just mention this for completeness. The patch dosn't touch the serial_cs driver which is causing me the problem. I've also checked against an unpatched 3.1.9 install. The problem is that the modem does not respond. If I load minicom, I can't get it to return an OK to ATZ and minicom hangs and will not quit if I try to shut it down until I remove the card. The card works in a Windows laptop (I can get an OK back from a terminal program) and should appear to be a generic modem. A Megahertz modem card works fine in this installation, From /var/log/messages: Jan 25 09:13:19 agape cardmgr[276]: initializing socket 0 Jan 25 09:13:19 agape cardmgr[276]: socket 0: Serial or Modem Jan 25 09:13:20 agape cardmgr[276]: executing: 'insmod /lib/modules/2.2.14-15mdksecure/pcmcia/serial_cs.o' Jan 25 09:13:20 agape kernel: tty02 at 0x13f8 (irq = 3) is a 16450 Jan 25 09:13:20 agape cardmgr[276]: executing: './serial start ttyS2' Two beeps on install. So far, so good. [root@agape linux]# dump_cis Socket 0: dev_info NULL 0ns, 512b vers_1 4.1, "Sierra Wireless", "Aircard Modem", "Version 1.0" manfid 0x0192, 0x0201 funcid serial_port [post] serial_data_services data_rate 115200 modulation [Bell103] [V.21] [V.23] [V.22] [Bell212A] [V.22bis] [V.27bis] [V.29] [V.32] [V.32bis] error_control [MNP2-4] [V.42/LAPM] compression [V.42bis] [MNP5] cmd_protocol [AT1] [AT2] [AT3] [MNP_AT] [V.25bis] serial_fax_services [class=1] data_rate 115200 modulation [V.21-C2] [V.27ter] [V.29] [V.17] features [T.4] config base 0x1000 mask 0x0007 last_index 0x23 cftable_entry 0x20 [default] [rdybsy] [audio] Vcc Vnom 5V Istatic 180mA Ipeak 220mA timing ready 3705032704ns io 0x03f8-0x03ff [lines=10] [8bit] [range] irq mask 0x86bc [level] cftable_entry 0x21 io 0x02f8-0x02ff [lines=10] [8bit] [range] cftable_entry 0x22 io 0x03e8-0x03ef [lines=10] [8bit] [range] cftable_entry 0x23 io 0x02e8-0x02ef [lines=10] [8bit] [range] everything looks cozy. From the startup of PCMCIA services: Jan 25 09:00:03 agape pcmcia: Starting PCMCIA services: Jan 25 09:00:03 agape pcmcia: modules Jan 25 09:00:04 agape kernel: Linux PCMCIA Card Services 3.1.9 Jan 25 09:00:04 agape kernel: kernel build: 2.2.14-15mdksecure #1 SMP Tue Jan 4 21:15:44 CET 2000 Jan 25 09:00:04 agape kernel: options: [pci] [cardbus] Jan 25 09:00:04 agape kernel: Intel PCIC probe: Jan 25 09:00:04 agape kernel: TI 1131 PCI-to-CardBus at bus 0 slot 6, mem 0x68000000, 2 sockets Jan 25 09:00:04 agape kernel: host opts [0]: [ring] [clkrun irq 10] [pci + serial irq] [no pci irq] [lat 64/176] [bus 1/1] Jan 25 09:00:04 agape kernel: host opts [1]: [ring] [clkrun irq 10] [pci + serial irq] [no pci irq] [lat 64/176] [bus 2/2] Jan 25 09:00:04 agape kernel: ISA irqs (scanned) = 3,4,7,10,15 polling interval = 1000 ms Jan 25 09:00:04 agape pcmcia: cardmgr. Jan 25 09:00:05 agape cardmgr[276]: starting, version is 3.1.9 Jan 25 09:00:05 agape rc: Starting pcmcia succeeded Jan 25 09:00:05 agape cardmgr[276]: watching 2 sockets Jan 25 09:00:05 agape kernel: cs: IO port probe 0x1000-0x17ff: clean. Jan 25 09:00:05 agape kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x200-0x207 0x220-0x22f 0x330-0x337 0x370-0x37f 0x388-0x38f 0x398-0x39f 0x4d0-0x4d7 Jan 25 09:00:05 agape kernel: cs: IO port probe 0x0a00-0x0aff: clean.

1. It's an IO port issue by David Hinds, 2000, Jan 25

Very strange situation - difficult to find a good title! Date: 2000, Feb 03 From: Alessandro Russo <russo@ian.pv.cnr.it>

I'm having different troubles with 2 modem cards. Configuration: System brand & model: Toshiba 4010CDT Linux version: 2.2.14 (mandrake 7.0) Pcmcia version: 3.1.9 ------------------------------------------------------------ 1) card: 56000bps UltraSpeed What happens is precisely the same as John Ruttenberg described in message 10. Everything is fine from the logs, but the modem doesn't work. But if I do (assuming that 5 was the irq assigned by pcmcia, but it works with other irqs) setserial /dev/modem irq 0 setserial /dev/modem irq 5 then everything is ok. Tha card can also be swapped. This card used to work perfectly with Suse 5.3 on the same computer. It works perfectly on a Toshiba 4030CDT with redhat 6.1 (kernel 2.2.12, PCMCIA 3.0.14) ----------------------------------------------------------- 2) card: 3COM 3CXM756 Global GSM and Modem PC Card What happens is similar to what described by Jaime V Miro in message 1. The UART detected is wrong, it is 8250 instead of 16550A (for the other card the UART detection is fine) and the modem doesn't work. I have not been able to make it working by changing UART and irq with setserial. Also this card works perfectly on my Toshiba 4030CDT with redhat 6.1 (kernel 2.2.12, PCMCIA 3.0.14) ---------------------------------------------------------- I also have a 3C598D ethernet CARD that works well in both computers and in all slots. Thanks in advance for your attention. Ciao Alessandro Russo IAN-CNR, Pavia (ITALY) ---------------------------------------------------- "Microsoft is learning a hard lesson with Linux, namely that there is more to life than product marketing" russo@ian.pv.cnr.it

1. At least the first part is fixed in 3.1.10 by David Hinds, 2000, Feb 03

Question: serial modem on Inspiron 3500 Date: 2000, Jan 03 From: Dirk Arnold dirk

Hello, I have an Inspiron 3500 running RH6.1 (kernel 2.2.12; pcmcia-3.0.14) and a Xircom RBM56G CardBus modem. probe yields PCI bridge probe: TI 1220 found, 2 sockets. The card is identified correctly but cannot be configured. Here's the relevant part of the system log: cardmgr[289]: initializing socket 0 cardmgr[289]: socket 0: Serial or Modem cardmgr[289]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/serial_cs.o' kernel: serial_cs: ParseTuple: No more items cardmgr[289]: get dev info on socket 0 failed: Resource temporarily unavaliable Is this fixed by a newer version of the pcmcia package? Any help very much appreciated. Dirk

Question: Trouble with FM560CB modem card Date: 2000, Feb 22 From: Martin Buck <mb@netwings.ch>

I've got a few problems with a FM560CB PCMCIA modem card (probably made by Abocom - http://www.abocom.com - although the package doesn't say anything about the manufacturer). If I plug it in (into a HP Omnibook 4150) with a unmodified PCMCIA config, I get the following: kernel: Linux PCMCIA Card Services 3.1.8 kernel: kernel build: 2.2.10 #8 Thu Oct 28 09:49:56 CEST 1999 kernel: options: [pci] [cardbus] [apm] kernel: Intel PCIC probe: kernel: TI 1220 PCI-to-CardBus at bus 0 slot 4, mem 0x68000000, 2 sockets kernel: host opts [0]: [pwr save] [serial pci & irq] [no pci irq] [lat 64/32] [bus 32/34] kernel: host opts [1]: [pwr save] [serial pci & irq] [no pci irq] [lat 64/32] [bus 35/37] kernel: ISA irqs (scanned) = 3,4,5,7,11 polling interval = 1000 ms cardmgr[1151]: starting, version is 3.1.8 cardmgr[1151]: watching 2 sockets kernel: cs: IO port probe 0x1000-0x17ff: clean. kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x120-0x127 0x220-0x22f 0x378-0x37f 0x388-0x38f kernel: cs: IO port probe 0x0a00-0x0aff: clean. cardmgr[1151]: initializing socket 1 kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. cardmgr[1151]: error parsing CIS on socket 1: Invalid argument cardmgr[1151]: unsupported card in socket 1 cardmgr[1151]: product info: "V90&K56Flex PCMCIA FAX MODEM", "", "", "" cardmgr[1151]: exiting So I added this to /etc/pcmcia/config: card "V90&K56Flex PCMCIA FAX MODEM" version "V90&K56Flex PCMCIA FAX MODEM", "", "", "" bind "serial_cs" Now the card is recognized, but configuration fails: kernel: Linux PCMCIA Card Services 3.1.8 kernel: kernel build: 2.2.10 #8 Thu Oct 28 09:49:56 CEST 1999 kernel: options: [pci] [cardbus] [apm] kernel: Intel PCIC probe: kernel: TI 1220 PCI-to-CardBus at bus 0 slot 4, mem 0x68000000, 2 sockets kernel: host opts [0]: [pwr save] [serial pci & irq] [no pci irq] [lat 64/32] [bus 32/34] kernel: host opts [1]: [pwr save] [serial pci & irq] [no pci irq] [lat 64/32] [bus 35/37] kernel: ISA irqs (scanned) = 3,4,5,7,11 polling interval = 1000 ms cardmgr[1354]: starting, version is 3.1.8 cardmgr[1354]: watching 2 sockets kernel: cs: IO port probe 0x1000-0x17ff: clean. kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x120-0x127 0x220-0x22f 0x378-0x37f 0x388-0x38f kernel: cs: IO port probe 0x0a00-0x0aff: clean. cardmgr[1354]: initializing socket 1 kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. cardmgr[1354]: error parsing CIS on socket 1: Invalid argument cardmgr[1354]: socket 1: V90&K56Flex PCMCIA FAX MODEM cardmgr[1354]: executing: 'insmod /lib/modules/2.2.10/pcmcia/serial_cs.o' kernel: register_serial(): autoconfig failed kernel: serial_cs: register_serial() at 0x02f8, irq 3 failed cardmgr[1354]: get dev info on socket 1 failed: Resource temporarily unavailable The "error parsing CIS" looks suspicious to me. Do I need a magic file that I can drop into /etc/pcmcia/cis to make the card work? BTW, this is what cis_dump -v has to say: Socket 0: no CIS present Socket 1: offset 0x02, tuple 0x01, link 0x01 d1 parse error: Invalid argument offset 0x05, tuple 0x15, link 0x2b 04 00 56 39 30 26 4b 35 36 46 6c 65 78 20 50 43 4d 43 49 41 20 46 41 58 20 4d 4f 44 45 4d 00 00 00 00 00 00 00 00 00 00 00 00 00 vers_1 4.0, "V90&K56Flex PCMCIA FAX MODEM", "", "", "" offset 0x32, tuple 0x20, link 0x02 02 00 parse error: Invalid argument offset 0x36, tuple 0x1a, link 0x05 01 23 00 01 03 config base 0x0100 mask 0x0003 last_index 0x23 offset 0x3d, tuple 0x1b, link 0x14 e1 81 9d 68 86 23 86 50 35 fc 15 aa 60 f8 02 07 30 b8 86 68 cftable_entry 0x21 [default] [mwait] [audio] [pwrdown] Vcc Istatic 135mA Ipeak 180mA Idown 30mA timing wait 120us io 0x02f8-0x02ff [lines=10] [8bit] [range] irq mask 0x86b8 [level] offset 0x53, tuple 0x1b, link 0x07 20 08 aa 60 f8 03 07 cftable_entry 0x20 io 0x03f8-0x03ff [lines=10] [8bit] [range] offset 0x5c, tuple 0x1b, link 0x07 22 08 aa 60 e8 03 07 cftable_entry 0x22 io 0x03e8-0x03ef [lines=10] [8bit] [range] offset 0x65, tuple 0x1b, link 0x07 23 08 aa 60 e8 02 07 cftable_entry 0x23 io 0x02e8-0x02ef [lines=10] [8bit] [range] Any hints? Thanks, Martin

1. Maybe a resource conflict by David Hinds, 2000, Feb 22 1. Sad: Don't think so by Martin Buck, 2000, Feb 23 2. More info by Martin Buck, 2000, Feb 24 1. Re: More info by David Hinds, 2000, Feb 24 ... 2 Message(s)

Sad: CIS parse errors on Lucent modem Date: 2000, Mar 02 From: Mark Neil holman

I have been trying to get an unbranded modem running on a Dell Latitude CPiA running Redhat 6.1 but without success. OK so it doesn't say WinModem on the box but the logged messages (see below) point to it being so. However there is also a complaint from the drivers "parse error: Invalid argument" when reading the CIS. dump_cis gives similar errors. I have tried upgrading from the standard 3.0.14 to 3.1.11 (in view of a brief mention of "Lucent Win Modems" in the CHANGES file) but the behaviour is the same. I have also messed with the /etc/pcmcia/config file in order to at least get it to try the serial module. Does anyone have any idea as to what is going on, or whether I should cut my losses in view of the Winmodem bit thanks Mark Neil ps there is also an ethernet card mentioned which works fine - the modem behaviour is the same whether or not the ethernet is inserted. from /var/log/messages: Mar 2 14:56:50 localhost kernel: Linux PCMCIA Card Services 3.1.11 Mar 2 14:56:50 localhost kernel: kernel build: 2.2.12-20 #1 Mon Sep 27 10:40:35 EDT 1999 Mar 2 14:56:50 localhost kernel: options: [pci] [cardbus] [apm] [pnp] Mar 2 14:56:50 localhost kernel: PCI routing table version 1.0 at 0xfbda0 Mar 2 14:56:50 localhost kernel: PnP: PNP BIOS installation structure at 0xc00fe2d0 Mar 2 14:56:50 localhost kernel: PnP: PNP BIOS version 1.0, entry at f0000:e2f4, dseg at 40 Mar 2 14:56:50 localhost kernel: Intel PCIC probe: Mar 2 14:56:50 localhost kernel: TI 1225 PCI-to-CardBus at slot 00:03, mem 0x68000000 Mar 2 14:56:50 localhost kernel: host opts [0]: [ring] [serial pci & irq] [pci irq 11] [lat 32/32] [bus 32/34] Mar 2 14:56:50 localhost kernel: host opts [1]: [ring] [serial pci & irq] [pci irq 11] [lat 32/32] [bus 35/37] Mar 2 14:56:50 localhost kernel: ISA irqs (scanned) = 3,9,10 PCI status changes Mar 2 14:56:50 localhost cardmgr[5916]: starting, version is 3.1.11 Mar 2 14:56:50 localhost cardmgr[5916]: watching 2 sockets Mar 2 14:56:50 localhost kernel: cs: IO port probe 0x1000-0x17ff: clean. Mar 2 14:56:50 localhost kernel: cs: IO port probe 0x0100-0x04ff: clean. Mar 2 14:56:50 localhost kernel: cs: IO port probe 0x0a00-0x0aff: clean. Mar 2 14:56:50 localhost cardmgr[5916]: initializing socket 0 Mar 2 14:56:50 localhost kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. Mar 2 14:56:50 localhost cardmgr[5916]: error parsing CIS on socket 0: Invalid argument Mar 2 14:56:50 localhost cardmgr[5916]: socket 0: LT WIN MODEM GLOBAL Mar 2 14:56:50 localhost cardmgr[5916]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/serial_cs.o' Mar 2 14:56:51 localhost kernel: register_serial(): autoconfig failed Mar 2 14:56:51 localhost kernel: serial_cs: register_serial() at 0x02f8, irq 3 failed Mar 2 14:56:52 localhost cardmgr[5916]: get dev info on socket 0 failed: Resource temporarily unavailable Mar 2 14:56:52 localhost cardmgr[5916]: initializing socket 1 Mar 2 14:56:52 localhost cardmgr[5916]: socket 1: NE2000 Compatible Ethernet Mar 2 14:56:52 localhost cardmgr[5916]: executing: 'insmod /lib/modules/2.2.12-20/net/8390.o' Mar 2 14:56:52 localhost cardmgr[5916]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/pcnet_cs.o' Mar 2 14:56:52 localhost kernel: eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:E0:98:1A:1E:16 Mar 2 14:56:52 localhost cardmgr[5916]: executing: './network start eth0'

1. The CIS problem is not really important by David Hinds, 2000, Mar 02

Question: How to configure Com1 V.90 MC221 Discovery on Sony Vaio F305 ? Date: 2000, Jan 31 From: Axel Stockburger red

hi there, as newbie I definitively need help setting up 2 Pcmcia Cards running on a Sony Vaio F-305 under Suse Linux. card 1 = Modemcard Com1 V.90 MC221 Discovery 56K (it is not supported by the package - but i think it should work if I could find out the right interrupts..)- but how ? card 2 = Ethernetcard Argosy EN 235 10/100 ( I think it is supported, but cardctl and cardmanager always say there is nothing loaded...) also I don`t know what to write into the config file... here is a boot.message printout: ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS02 at 0x03e8 (irq = 4) is a 16550A Linux PCMCIA Card Services 3.1.3 kernel build: 2.2.13 #1 Mon Nov 8 18:28:35 GMT 1999 options: [pci] [cardbus] [pnp] PnP: PNP BIOS installation structure at 0xc00f6e00 PnP: PNP BIOS version 1.0, entry at f0000:b54f, dseg at 400 PCI routing table version 1.0 at 0xfdf60 00:0a.0 -> irq 9 Intel PCIC probe: Ricoh RL5C478 PCI-to-CardBus at bus 0 slot 10, mem 0x68000000, 2 sockets host opts [0]: [isa irq] [io 3/6/1] [mem 3/6/1] [pci irq 9] [lat 168/176] [bus 32/34] host opts [1]: [isa irq] [io 3/6/1] [mem 3/6/1] [no pci irq] [lat 168/176] [bus 35/37] ISA irqs (default) = 3,4,5,7,10,11,12 polling interval = 1000 ms cs: IO port probe 0x1000-0x17ff: clean. cs: IO port probe 0x0100-0x04ff: clean. cs: IO port probe 0x0a00-0x0aff: clean. cs: cb_alloc(bus 32): vendor 0x10ec, device 0x8138 cs: cb_alloc(bus 35): vendor 0xffff, device 0x0440 hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x50 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid field in command packet -- (asc=0x24, ascq=0x00) The failed "Start Stop Unit" packet command was: "1b 00 00 00 03 00 00 00 00 00 00 00 " Error in command packet byte 256 bit 0 cdrom: open failed. VFS: Disk change detected on device ide1(22,0) to be honest, I don`t really know what it means... pleeeeez help me ... thanx in advance red

1. Neither card is supported by David Hinds, 2000, Jan 31

Modem only works with irq 0 Date: 2000, Feb 03 From: Bennett Link blink

I recently upgraded from Redhat 5.2 to 6.1 on a Sony N505VX notebook. The PCMCIA modem, which worked fine under RH 5.2, now works only if I manually set the irq of /dev/ttyS1 to 0. I've verified that no other irq works by excluding different irq values in /etc/pcmcia/config.opts. My pcmcia lan card works fine. I am using pcmcia card services 3.1.8, which I recompiled using the defaults after installing the new kernel. According to the system log, cardmgr is correctly identifying the card as a modem and loading the serial_cs module: .... Feb 3 09:01:02 beatrice cardmgr[331]: initializing socket 0 Feb 3 09:01:02 beatrice kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. Feb 3 09:01:02 beatrice cardmgr[331]: socket 0: Serial or Modem Feb 3 09:01:02 beatrice cardmgr[331]: module /lib/modules/preferred/misc/serial.o not available Feb 3 09:01:02 beatrice cardmgr[331]: executing: 'insmod /lib/modules/preferred/pcmcia/serial_cs.o' Feb 3 09:01:02 beatrice kernel: tty01 at 0x13f8 (irq = 4) is a 16550A Feb 3 09:01:02 beatrice cardmgr[331]: executing: './serial start ttyS1' .... lsmod gives: Module Size Used by serial_cs 5168 0 (unused) ds 6472 1 [serial_cs] i82365 29536 1 pcmcia_core 43936 0 [serial_cs ds i82365] opl3 11208 0 (unused) sb 33620 0 uart401 5968 0 [sb] sound 57240 0 [opl3 sb uart401] soundlow 300 0 [sound] soundcore 2372 6 [sb sound] And setserial on /dev/modem gives: /dev/modem, UART: 16550A, Port: 0x13f8, IRQ: 4 /proc/interrupts shows: CPU0 0: 366286 XT-PIC timer 1: 4193 XT-PIC keyboard 2: 0 XT-PIC cascade 5: 1 XT-PIC soundblaster 8: 1 XT-PIC rtc 12: 61070 XT-PIC PS/2 Mouse 13: 1 XT-PIC fpu 14: 131017 XT-PIC ide0 NMI: 0 Thanks for any help, Bennett blink@dante.physics.montana.edu

1. There is a workaround in the 3.1.10 driver package by David Hinds, 2000, Feb 03

Question: Modem IO error Date: 2000, Apr 16 From: Pawel Konieczny konieczp

This is a cross-post from comp.os.linux.portable (sorry David, I couldn't help it, maybe somebody here recognises the problem): The card is properly recognised by the cardmgr, which assigns ttyS1 to it, but when I try to use /dev/ttyS1 I get an "input/output error" (if root) or "Operation not allowed for device" (if user). Does anybody recognise the problem? Do you know the solution? It seems a configuration problem to me, rather than a PCMCIA problem, but I really don't know. I am new to Linux (two weeks). Pawel Here are some details for those of you who are ready to help me: Laptop: DELL Latitude CPi System: Debian GNU/Linux 2.1 (try Linux because of the free software idea, not ease of use) Linux kernel 2.2.12 PCMCIA: original: ii pcmcia-cs 3.0.14-0slink1 PCMCIA Card Services for Linux. upgraded to: 3.1.8 Tried two different cards: RBEM56G-100 (Xircom RealPort CardBus Ethernet 10/100+Modem 56) CM33 (Xircom GlobalAccess CreditCard Modem 33.6) -- both recognised and configured smoothly by cardmgr Here is the contents of /var/state/pcmcia/stab for the first card: Socket 0: empty Socket 1: Xircom CardBus 10/100 Ethernet + 56K Modem 1 network tulip_cb 0 eth0 1 serial serial_cb 0 ttyS1 4 65 Here is the contents of /var/state/pcmcia/stab for the second card: Socket 0: Serial or Modem 0 serial serial_cs 0 ttyS1 4 65 Socket 1: empty $ ls -l /dev/ttyS1 crw-rw-rw- 1 root dialout 4, 65 Sep 9 1999 /dev/ttyS1 Things I tied (without success) * read all serial-port or PCMCIA related HOWTOS * scan for existing posts to newsgroups on this subject * laptop istallation tips published on the web (selectively) * disabled infrared ports in BIOS * upgraded BIOS to the latest (two months old) * upgraded pcmcia package to the latest stable release 3.1.8 * inserted and removed the card several times (recognition OK) * tried an external modem on ttyS0 - works fine * ifconfig eth0 down * modified /etc/pcmcia/config not to load tulip_cb for RBEM56G-100(tulip_cb is tagged as "unreliable" in PCMCIA HOWTO, but funny enough, my eth0 works fine with it!) * Upgraded to PCMCIA 3.1.14 * Removed /dev/ttyS1 - cardmgr recreated it at insertion

1. Fixed in 3.1.14 by David Hinds, 2000, Apr 19 (_ Ok: It is, indeed! by Pawel Konieczny, 2000, Apr 25

Question: Hawking pcmcia installation trouble Date: 2000, Apr 21 From: ed bailey erb

Hi, I am trying to install a Hawking PN610 pcmcia modem on a Winbook XL2 running SUSE 6.4 with serial support compiled into the kernel. When I first inserted the card, the cardmanger listed the card as unsupported at bootup. Using cardctl ident I wrote a new config entry into /etc/pcmcia/config card "Hawking V.90" manfid 0x018a, 0x0001 bind "serial_cs" and then rebooted Then the cardmanger recognized my entry and executed and then gave the following error message - "probing for dev info failed - resource temporaily unavailible." When I run dmesg I get the following register_serial(): autoconfig failed serial_cs: register_serial() at 0x02f8, irq failed Does any body have any ideas about what I should do - I have been messing with this for some time. Thank you in advance for any help you can provide. Ed

1. register_serial(): autoconfig failed by David Hinds, 2000, Apr 21 2. Sad: Probably a WinModem by David Hinds, 2000, Apr 21

Question: error parsing CIS (Hamlet modem) Date: 2000, May 18 From: Aram Gurekian aram

Hi all... I'm a newbie in linux and hardware, so please be patient if my questions are silly! :) I have an Hamlet FM560 56K - V.90 PCMCIA FAX MODEM. It works fine on my windoz98 partition, but I can't make it work with linux! :( I'm pretty sure that it isn't a winmodem (at least, I can't read 'winmodem' in any part of the documentation! :) ) I'd like to get rid of this 1GB vfat partition, but I can't until I can connect to the internet without windows! I spent a few hours reading documentation under /usr/doc, but now I think that at this point I need some help... I have also a PCMCIA Ethernet Card from Hamlet and it works fine with both windows and linux in the other pcmcia slot. I still can't understand if my card is supported or not. I wouldn't be able (at the moment) to write a new driver, so I'm probably going to buy a supported modem (even an external one)... it would probably have been more convenient to do that from the beginning, but I wanted to try... in fact I learnt some interesting things, but now I'm done! :P ... I guess every answer is in the "Error parsing CIS on socket 1: Invalid argument I tried to report as many information about my system (maybe too many?) as I could. Any help or explanation would be appreciated. Thank you in advance! Ciao   Aram Gurekian Hardware -------- Texas Instruments extensa 710DX pentium 233 MMX it has an internal modem that died some time ago :) uname -a -------- Linux spiff.weirdo 2.2.12-20 #1 Mon Sep 27 10:40:35 EDT 1999 i686 unknown I use RedHat 6.1 and card services that came along with it windows 98 ---------- PCMCIA FAX MODEM 56K HAMLET FM560 56K-V.90 PORT:COM3 IO: 0x03e8-0x03ef interrupt: 10 (or sometimes 9) CONTROLLER CARDBUS T.I. PCI-1250 interrupt:11 memory interval: 0x8c001000-0x8c001fff /etc/rc.d/init.d/pcmcia stop - pcmcia start: -------------------------------------------- May 18 17:21:57 spiff cardmgr[1888]: executing: './network check eth0' May 18 17:21:57 spiff cardmgr[1888]: shutting down socket 0 May 18 17:21:57 spiff cardmgr[1888]: executing: './network stop eth0' May 18 17:21:57 spiff cardmgr[1888]: executing: 'rmmod pcnet_cs' May 18 17:21:57 spiff cardmgr[1888]: executing: 'rmmod 8390' May 18 17:21:57 spiff cardmgr[1888]: shutting down socket 1 May 18 17:21:57 spiff cardmgr[1888]: executing: 'rmmod serial_cs' May 18 17:21:57 spiff cardmgr[1888]: exiting May 18 17:21:59 spiff kernel: unloading PCMCIA Card Services May 18 17:22:01 spiff kernel: Linux PCMCIA Card Services 3.0.14 May 18 17:22:01 spiff kernel: kernel build: 2.2.12-20 #1 Mon Sep 27 10:40:35 E DT 1999 May 18 17:22:01 spiff kernel: options: [pci] [cardbus] [apm] May 18 17:22:01 spiff kernel: Intel PCIC probe: May 18 17:22:01 spiff kernel: TI 1250A PCI-to-CardBus at bus 0 slot 6, mem 0x6 8000000, 2 sockets May 18 17:22:01 spiff kernel: host opts [0]: [pwr save] [serial pci & irq] [ no pci irq] [lat 168/176] [bus 32/34] May 18 17:22:01 spiff kernel: host opts [1]: [pwr save] [serial pci & irq] [ no pci irq] [lat 168/176] [bus 35/37] May 18 17:22:01 spiff kernel: ISA irqs (scanned) = 3,4,7,9,10 status changeon irq 10 May 18 17:22:01 spiff cardmgr[2013]: starting, version is 3.0.14 May 18 17:22:01 spiff cardmgr[2013]: watching 2 sockets                                                                                May 18 17:22:01 spiff kernel: cs: IO port probe 0x1000-0x17ff: excluding 0x1000- 0x104f May 18 17:22:01 spiff kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x378-0 May 18 17:22:01 spiff cardmgr[2013]: initializing socket 0 May 18 17:22:01 spiff kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. May 18 17:22:01 spiff cardmgr[2013]: socket 0: NE2000 Compatible Ethernet May 18 17:22:02 spiff cardmgr[2013]: executing: 'insmod /lib/modules/2.2.12-20/net/8390.o' May 18 17:22:02 spiff cardmgr[2013]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/pcnet_cs.o' May 18 17:22:02 spiff kernel: eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:E0:98:19:2C:79 May 18 17:22:02 spiff cardmgr[2013]: executing: './network start eth0' May 18 17:22:02 spiff cardmgr[2013]: initializing socket 1 May 18 17:22:02 spiff cardmgr[2013]: error parsing CIS on socket 1: Invalid argument May 18 17:22:02 spiff cardmgr[2013]: socket 1: V90&K56Flex PCMCIA FAX MODEM May 18 17:22:02 spiff cardmgr[2013]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/serial_cs.o irq_list=9,10' May 18 17:22:03 spiff kernel: register_serial(): autoconfig failed May 18 17:22:03 spiff kernel: serial_cs: register_serial() at 0x03e8, irq 9 failed May 18 17:22:04 spiff cardmgr[2013]: get dev info on socket 1 failed: Resource temporarily unavailable cardctl ident: -------------- Socket 0:   product info: "Ethernet", "Adapter", "2.0"   manfid: 0x0149, 0xc1ab   function: 6 (network) Socket 1:   product info: "V90&K56Flex PCMCIA FAX MODEM", "", "", "" /etc/pcmcia/config ------------------ device "serial_cs"   class "serial" module "serial_cs" # tried even with -> opts "irq_list=9,10" # I tried to add this lines to the file: card "V90&K56Flex PCMCIA FAX MODEM"   version "V90&K56Flex PCMCIA FAX MODEM"   bind "serial_cs" /etc/pcmcia/config.opts ----------------------- # # Local PCMCIA Configuration File # # System resources available for PCMCIA devices # include port 0x100-0x4ff, port 0x1000-0x17ff # tried even to add those three rows (data taken from windows behaviour) #include port 0x3e8-0x3ef #include irq 11, irq 9 #include memory 0x8c001000-8c001fff # end include memory 0xc0000-0xfffff include memory 0xa0000000-0xa0ffffff, memory 0x60000000-0x60ffffff # # Extra port range for IBM Token Ring # include port 0xa00-0xaff # # Resources we should not use, even if they appear to be available # # First built-in serial port exclude irq 4 # Second built-in serial port #exclude irq 3 # First built-in parallel port exclude irq 7 /etc/sysconfig/pcmcia --------------------- PCMCIA=yes PCIC=i82365 PCIC_OPTS= CORE_OPTS= /proc/interrupts ----------------            CPU0   0: 556368 XT-PIC timer   1: 14633 XT-PIC keyboard   2: 0 XT-PIC cascade   3: 62 XT-PIC pcnet_cs   8: 1 XT-PIC rtc  10: 69 XT-PIC i82365  12: 82085 XT-PIC PS/2 Mouse  13: 1 XT-PIC fpu  14: 467685 XT-PIC ide0  15: 47011 XT-PIC ide1 NMI: 0 /proc/ioports ------------- 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-007f : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 02f8-02ff : serial(auto) 0300-031f : pcnet_cs 0376-0376 : ide1 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial(auto) fcd0-fcd7 : ide0 fcd8-fcdf : ide1

1. The CIS error is harmless, not the problem by David Hinds, 2000, May 23

Question: Nokia CardPhone 1.0 Problem Date: 2000, May 18 From: Michael D. md

Hi everyone, I`m trying to install a Nokia CardPhone 1.0 on a SuSE 6.2 System (Kernel 2.2.10) with the pcmcia package 3.1.14 newly compiled. Mashine is a Toshiba Satellite 2550CDT. I managed to configure my D-Link 650TX Ethernet Card thanks to your lists here but I`m stuck with the Nokia card. Here the output: Serial driver version 4.27 with SHARE_IRQ enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A Linux PCMCIA Card Services 3.1.14 kernel build: 2.2.10 #7 Sun Aug 15 20:23:47 MEST 1999 options: [pci] [cardbus] [apm] PCI routing table version 1.0 at 0xf0180 Intel PCIC probe: Intel i82365sl B step rev 00 ISA-to-PCMCIA at port 0x3e0 ofs 0x00 host opts [0]: none host opts [1]: none ISA irqs (scanned) = 3,4,5,7,10 polling interval = 1000 ms cs: IO port probe 0x1000-0x17ff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. cs: memory probe 0x0d0000-0x0dffff: clean. eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:E0:98:77:95:07 tty01 at 0x0100 (irq = 5) is a 16450 register_serial(): autoconfig failed serial_cs: register_serial() at 0x0108, irq 5 failed What is the problem here? What means the last line (why 0x0108 and not 0x0100???) What can I try? Thank you for every hint! Michael

1. There is a specific Nokia driver for linux by David Hinds, 2000, May 18 (_ Yes but it`s for pcmcia 2.9.12... by Michael D., 2000, May 19 (_ Re: Yes but it`s for pcmcia 2.9.12... by David Hinds, 2000, May 19

Question: modem looks like it is working but I cannot communicate with it Date: 2000, May 19 From: Randy Smith randysmith

I have a TI cardbus controller and a modem card. Here are the log files... pcmcia start Linux PCMCIA Card Services 3.1.15 kernel build: 2.2.15 #1 Thu May 11 16:19:36 EDT 2000 options: [pci] [cardbus] [pnp] PCI routing table version 1.0 at 0xf82b0 PnP: PNP BIOS installation structure at 0xc00f7bd0 PnP: PNP BIOS version 1.0, entry at f0000:7344, dseg at f0000 Intel PCIC probe: TI 1221 rev 00 PCI-to-CardBus at slot 00:10, mem 0x68000000 host opts [0]: [pci only] [pci irq 10] [lat 168/176] [bus 32/34] host opts [1]: [pci only] [pci irq 10] [lat 168/176] [bus 35/37] PCI card interrupts, PCI status changes cardmgr[634]: starting, version is 3.1.15 cardmgr[634]: watching 2 sockets cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0800-0x08ff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x110-0x117 cs: IO port probe 0x0a00-0x0aff: clean. insert the modem card: (two high beeps heard) cardmgr[634]: initializing socket 0 cardmgr[634]: socket 0: Cirrus Logic 14.4K Fax Modem cs: memory probe 0xa0000000-0xa0ffffff: clean. cardmgr[634]: executing: 'modprobe serial_cs' tty02 at 0x0af8 (irq = 10) is a 16550A cardmgr[634]: executing: './serial start ttyS2' At this point it looks like it should be working, but I cannot communicate with the card. randys:/etc/pcmcia # ditty /dev/ttyS2 TCGETA: I/O error Now, I also have another pcmcia interface that plugs into the ISA bus. This modem works with that interface just fine. The above "ditty" will show the current config status of it. Any suggestions? Randy Smith

1. A bug; fixed in the 19-May-00 beta drivers by David Hinds, 2000, May 19 (_ More: That fixed the modem by Randy Smith, 2000, May 19

Question: Kingmax PCMCIA modem Date: 2000, May 26 From: Grady Luffman Grady

...trying to get a Kingmax PCMCIA modem card to work on a laptop running RH Linux 6.1. Here's the dump: The card is listed in the Linux Modem Compatibility Index (with no defining information): Kingmax Technology, MGA-FM336C-KF. (not supported?) The socket controller is the Cirrus Logic PD6729 PCI-to-PCMCIA bridge, located at bus 0 slot 24, port 0x3000, with 2 sockets: 1. The PCIC probe is picking up the controller correctly (as "Cirrus PD6729 PCI-to-PCMCIA bridge...) 2. /proc/pci shows device at bus 0, slot 24, I/O at 0x3000 [0x3001], slow devsel 3. /etc/sysconfig/hwconf shows: class: other bus: PCI detached: 0 driver : Card: Cirrus Logic GD6729 desc: "Cirrus Logic | CL6729" vendorID: 1013 deviceID: 1100 4. 'lsmod' shows the i82365 and pcmcia_core modules loaded 5. /proc/ioports shows i82365 at 0x3000-0x3001 The controller appears to be functioning properly. The problem I think, is with the modem card. Initially, when I first ran the startup script, 'cardmgr' mis-identified the modem card as an SVEC 10/100 Fast Ethernet Card which is bound to 'tulip_cb' (which caused memory problems). Since then, I've changed the entry in /pcmcia/config several times in an effort to get the card identified (without success). But at least now the cardmgr is beeping when you insert/remove the card. (Low beep on insertion). Funny though, different entries in the config file have resulted in 'cardctl' showing different 'manfid' numbers. Should the 'manfid' entries be the same as the 'vendor ID' and 'device ID' shown in 'hwconf'? According to all I've read, I want to believe the card should work! I think I just need the correct entry to define the card in /pcmcia/config. Any ideas? Thanks!

1. Note: solved by Grady Luffman, 2000, May 26

Question: PCMCIA modem unresponsive Date: 2000, May 17 From: Johan Mellberg mellberg

Hi! I'm having some trouble setting up pcmcia (I have only one modem so I don't now if it might be related to that specifically) - the modem just does not seem to exist. However it works just fine under Windows95 on the same machine (using it now). I know people are using pcmcia on this machine with Linux so it should not be impossible! So what happens? When cardmgr starts up I hear two high beeps and I can just see the LEDs flash briefly. The card seems properly configured (see below). However, minicom says it is initialising the modem (/dev/ttyS1 - I have tried changing this with no change in behaviour) but nothing happens, seyon and kppp both complain that there is no modem. If I 'setserial /dev/modem irq 0' kppp _seems_ to work but the modem is completely inactive. Same thing if I do it with /dev/ttyS1. I can achieve the same if I exclude irq 9 and 11 in config.opts. Any information on what I need to do to make this work would be appreciated - and it should be noted that I do not understand what the significance (if any?) of the I/O range info from windows is in relation to the settings in config.opts (see below). Please find the following output enclosed: - specifications/setup - windows95 info - cardctl config - cardctl ident - config.opts - 'ls -l /dev/modem' and 'ls -l /dev/ttyS1' - /var/state/pcmcia/stab - relevant parts of /var/log/messages * Specs Omnibook 800CT (166MMX), 80MB RAM BIOS is set to 'PCIC-compatible', other options are 'Disable' and 'Cardbus' Slackware7/Windows95 dualboot with LILO Kernel updated to 2.2.15 pcmcia 3.1.14 installed from scratch * Windows95 pcmcia card/socket info Socket input/output range: 03E0-03E1 pcmcia modem on COM2, irq3, I/O range: 02F8-02FF * cardctl config ================ Socket 0:   Vcc 5.0V Vpp1 0.0V Vpp2 0.0V   interface type is "memory and I/O"   irq 3 [exclusive] [level]   Speaker output is enabled   function 0:     config base 0xff80       option 0x57 status 0x08 pin 0x00     io 0x02f8-0x02ff [8bit] Socket 1:   not configured * cardctl ident =============== Socket 0:   product info: "Ericsson", "K56CC"   manfid: 0x0200, 0x0001   function: 2 (serial) Socket 1:   no product info available Socket 0: Serial or Modem 0 serial serial_cs 0 ttyS1 4 65 Socket 1: empty * devices ========= lrwxrwxrwx 1 root root 10 May 17 09:49 /dev/modem -> /dev/ttyS1 crw-rw---- 1 root tty 4, 65 May 16 23:57 /dev/ttyS1 * /var/log/messages =================== May 17 09:49:21 violator kernel: Linux PCMCIA Card Services 3.1.14 May 17 09:49:21 violator kernel: kernel build: 2.2.15 #1 Tue May 9 18:13:58 CEST 2000 May 17 09:49:21 violator kernel: options: [pci] [cardbus] [apm] [pnp] May 17 09:49:21 violator kernel: PCI routing table version 1.0 at 0xf36e0 May 17 09:49:21 violator kernel: unknown PCI interrupt router 1004:0102 May 17 09:49:21 violator kernel: PnP: PNP BIOS installation structure at 0xc00ff000 May 17 09:49:21 violator kernel: PnP: PNP BIOS version 1.0, entry at e8000:33e1, dseg at e8000 May 17 09:49:21 violator kernel: Intel PCIC probe: May 17 09:49:21 violator kernel: TI 1131 rev 01 PCI-to-CardBus at slot 00:04, mem 0x68000000 May 17 09:49:21 violator kernel: host opts [0]: [clkrun irq 10] [serial pci & irq] [no pci irq] [lat 64/32] [bus 32/34] May 17 09:49:21 violator kernel: host opts [1]: [clkrun irq 10] [serial pci & irq] [no pci irq] [lat 64/32] [bus 35/37] May 17 09:49:21 violator kernel: ISA irqs (scanned) = 3,9,11,15 status change on irq 15 May 17 09:49:21 violator cardmgr[143]: starting, version is 3.1.14 May 17 09:49:21 violator cardmgr[143]: watching 2 sockets May 17 09:49:21 violator kernel: cs: IO port probe 0x0c00-0x0cff: clean. May 17 09:49:21 violator kernel: cs: IO port probe 0x0800-0x08ff: clean. May 17 09:49:21 violator kernel: cs: IO port probe 0x0100-0x04ff: clean. May 17 09:49:22 violator cardmgr[143]: initializing socket 0 May 17 09:49:22 violator kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. May 17 09:49:22 violator cardmgr[143]: socket 0: Serial or Modem May 17 09:49:22 violator cardmgr[143]: executing: 'insmod /lib/modules/2.2.15/pcmcia/serial_cs.o' May 17 09:49:22 violator kernel: tty01 at 0x02f8 (irq = 3) is a 16550A May 17 09:49:22 violator cardmgr[143]: executing: './serial start ttyS1' * config.opts ============= # # Local PCMCIA Configuration File # #---------------------------------------------------------------------- # System resources available for PCMCIA devices include port 0x100-0x4ff, port 0x800-0x8ff, port 0xc00-0xcff include memory 0xc0000-0xfffff include memory 0xa0000000-0xa0ffffff, memory 0x60000000-0x60ffffff # High port numbers do not always work... #include port 0x1000-0x17ff # Extra port range for IBM Token Ring #include port 0xa00-0xaff # Resources we should not use, even if they appear to be available # First built-in serial port exclude irq 4 # Second built-in serial port #exclude irq 3 # First built-in parallel port exclude irq 7

Question: socketcom serial adaptor with ricochet modem Date: 2000, May 31 From: Cengiz Alaettinoglu cengiz

Hi, I am having difficulty with Socketcom serial adaptor S-I/O card when I use it with my ricochet cellular modem. The card is recognized, ttyS1 is configured, and a ppp connection is established, however pppd fails to configure the interface with an IP address. My ricochet setup works with the builtin serial port, i.e. ttyS0 (unfortunately this requires me to carry a port replicator). I am including some diagnostics information. Did anyone seen similar problems or have any suggestions for me to try? Thank you Cengiz # tail -f /var/log/messages May 30 20:56:00 elf cardmgr[1995]: socket 0: Serial or Modem May 30 20:56:00 elf cardmgr[1995]: executing: 'insmod /lib/modules/2.2.14/pcmcia/serial_cs.o' May 30 20:56:00 elf kernel: tty01 at 0x02f8 (irq = 3) is a ST16650V2 May 30 20:56:00 elf cardmgr[1995]: executing: './serial start ttyS1' # cardctl ident Socket 0: product info: "Socket", "Serial Port Card Rev 2.4" manfid: 0x0104, 0x0001 function: 2 (serial) # more /var/state/pcmcia/stab Socket 0: Serial or Modem 0 serial serial_cs 0 ttyS1 4 65 #ifup ppp0 #tail -f /var/log/messages (on another terminal in parallel) May 30 20:58:06 elf ifup-ppp: pppd started for ppp0 on /dev/ttyS1 at 38400 May 30 20:58:06 elf kernel: registered device ppp0 May 30 20:58:06 elf pppd[2127]: pppd 2.3.11 started by root, uid 0 May 30 20:58:07 elf chat[2137]: abort on (BUSY) May 30 20:58:07 elf chat[2137]: abort on (ERROR) May 30 20:58:07 elf chat[2137]: abort on (NO CARRIER) May 30 20:58:07 elf chat[2137]: abort on (NO DIALTONE) May 30 20:58:07 elf chat[2137]: abort on (Invalid Login) May 30 20:58:07 elf chat[2137]: abort on (Login incorrect) May 30 20:58:07 elf chat[2137]: send (ATZ^M) May 30 20:58:07 elf chat[2137]: expect (OK) May 30 20:58:07 elf chat[2137]: ATZ^M^M May 30 20:58:07 elf chat[2137]: OK May 30 20:58:07 elf chat[2137]: -- got it May 30 20:58:07 elf chat[2137]: send (ATDT777^M) May 30 20:58:07 elf chat[2137]: expect (CONNECT) May 30 20:58:07 elf chat[2137]: ^M May 30 20:58:09 elf chat[2137]: ATDT777^M^M May 30 20:58:09 elf chat[2137]: CONNECT May 30 20:58:09 elf chat[2137]: -- got it May 30 20:58:09 elf chat[2137]: send (^M) May 30 20:58:09 elf pppd[2127]: Serial connection established. May 30 20:58:09 elf pppd[2127]: Using interface ppp0 May 30 20:58:09 elf pppd[2127]: Connect: ppp0 <--> /dev/ttyS1 I tried to debug pppd manually. % minicom Welcome to minicom 1.83.0 OPTIONS: History Buffer, F-key Macros, Search History Buffer, I18n Compiled on Mar 7 2000, 06:12:31. Press CTRL-A Z for help on special keys AT S7=45 S0=0 L1 OK atdt 777 CONNECT 38400 ~ÿ}#.!}!}"} }8}!}$}%Ü}"}&} } } } }%}&..j}^}'}"}(}"å/~~ÿ}#.!}!}#} }8}!}$}%Ü}"}&}~ #pppd -d -detach /dev/ttyS1 38400 mru 1500 Using interface ppp0 Connect: ppp0 <--> /dev/ttyS1 sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] rcvd [LCP ConfReq id=0x6 <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <a ccomp>] sent [LCP ConfAck id=0x6 <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <a ccomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] rcvd [LCP ConfReq id=0x7 <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <a ccomp>] sent [LCP ConfAck id=0x7 <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <a ccomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] rcvd [LCP ConfReq id=0x8 <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <a ccomp>] sent [LCP ConfAck id=0x8 <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <a ccomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] rcvd [LCP ConfReq id=0x9 <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <a ccomp>] sent [LCP ConfAck id=0x9 <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <a ccomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] rcvd [LCP ConfReq id=0xa <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <accomp>] sent [LCP ConfAck id=0xa <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] rcvd [LCP ConfReq id=0xb <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <accomp>] sent [LCP ConfAck id=0xb <mru 1500> <asyncmap 0x0> <magic 0xb4886a7e> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1bd3379d> <pcomp> <accomp>] LCP: timeout sending Config-Requests Connection terminated.

1. It's strange that the connection starts up ok by David Hinds, 2000, Jun 01 (_ Ok: "setserial /dev/ttyS1 uart 16550A" did the trick by Cengiz Alaettinoglu, 2000, Jun 01

Sad: EtherFast 10/100 + 56k problem Date: 2000, Jun 13 From: David Arnold darnold78

Okay, a bit of mess but here it is. RH 6.2, PCMCIA 3.1.15, EtherFast 10/100 +56K modem. eth cable/connection works great. Take the eth cable out, plug it back in, no problems. But the modem.. If you take the eth cable out, then insert the phone cable into the modem slot, test_modem will always return a poll error or such. The weird thing, test_modem will always work when the eth cable is plugged in! I've tried configuring /etc/pcmcia/config.opts, commenting out the various lines and restarting cardmgr, to no avail. You have to eject the card, plug in the modem cable, then insert back to get the modem recognised. This is bearable but there should be an easier way... David

1. You may have to live with it for now by David Hinds, 2000, Jun 14 (_ Feedback: Semi-workaround by David Arnold, 2000, Jun 14

Question: Configuring Quatech serial ports for specific devices Date: 2000, Jun 20 From: Jaime V Miro jaime

Hi, I've bought and installed a dual serial Quatech PCMCIA card (DSP-100) in my laptop. The laptop has got one serial port in /dev/ttyS0, and a secondary one for the infrared which I've diabled in BIOS. Linux (RH6.1) works fine and locates /dev/ttyS0, and cardmgr identifies the card with the 2 additional ports. However, when it configures the ports, these are not assigned to the next available devices, /dev/ttyS1 and /dev/ttyS2, which according to what I've read in the PCMCIA HOWTO documentation, I believe should happen. It is a small inconvenience that would normally not bother me. So long as I know which dev's to address the ports to, no probs. However, I've got an application that runs on various Linux machines, and I'd like not to have to recompile it every time I run it in the laptop. Q: is there a way to force cardmsg to assign the ports to specific devices? (I would only need one from the dual serial PCMCIA card, the other is not in use) Thanks in advance Jaime

1. There are several options by David Hinds, 2000, Jun 20

Question: 3COM 3CXM756 PCMCIA modem not working Date: 2000, Jun 25 From: capkapak

Anyone please help. I have tried to get a 3Com MegaHertz 3CXM756 PCMCIA modem to work with Red Hat 6.2 with kernel 2.2.14-12 but with no luck at all. I tried a Psion DACOM Gold card and it works fine. When I insert the 3Com card I hear the two beeps indicating that the card has been recongnised. Check the messages log and it indicates that the card has been identified as a serial device but as a 16450 UART and not 16550. Have tried everything from using setserial to set the IRQ to 0 to re-configuring the "config" script in /etc/pcmcia/ but with no luck whatsoever. Does anyone have been successful in utilising this particular PCMCIA modem in Linux? Thanks.

1. This might be an IO port conflict by David Hinds, 2000, Jul 08 2. Question: same problem can you give me info ? by jean-raymond Chauviere, 2000, Aug 28

Question: Socket dual rs-232 pcmcia... rev 2.1 Date: 2000, Jun 26 From: john gwynne <jsg@mrcday.com>

system: RH6.2 on winbook XP PCMCIA card: Socket "Dual Serial I/O Card Rev 2.1" kernel: redhat's 2.2.16-3 with pcmcia 3.1.17 I'm having problems trying to use a Socket "Dual Serial I/O Card" with the following identity: [root@efi /root]# /sbin/cardctl ident 0 product info: "Socket", "Dual I/O Card Rev 2.1" manfid: 0x0104, 0x0070 function: 2 (serial) This card is listed as supported; however, maybe the card I have is a later version that fails???? The card is detected (positive beeps) with the following kernel messages: ============================================================== Jun 26 17:00:24 efi pcmcia: cardmgr. Jun 26 17:00:24 efi rc: Starting pcmcia succeeded Jun 26 17:00:24 efi cardmgr[376]: starting, version is 3.1.17 Jun 26 17:00:24 efi cardmgr[376]: watching 2 sockets Jun 26 17:00:24 efi kernel: cs: IO port probe 0x1000-0x17ff: excluding 0x1000-0x100f 0x1018-0x1027 0x1040-0x1047 0x1060-0x1067 0x1080-0x1097 0x10a0-0x10a7 0x10c0-0x10d7 0x10f0-0x10f7 0x11f0-0x11f7 0x1268-0x126f 0x12f8-0x12ff 0x1378-0x137f 0x13f0-0x140f 0x1418-0x1427 0x1440-0x1447 0x1460-0x1467 0x1480-0x1497 0x14a0-0x14a7 0x14c0-0x14d7 0x14f0-0x14f7 0x15f0-0x15f7 0x1668-0x166f 0x16f8-0x16ff 0x1778-0x177f 0x17f0-0x17ff Jun 26 17:00:24 efi kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x100-0x107 0x268-0x26f 0x378-0x37f 0x400-0x40f 0x418-0x427 0x440-0x447 0x460-0x467 0x480-0x497 0x4a0-0x4a7 0x4c0-0x4d7 0x4f0-0x4f7 Jun 26 17:00:24 efi kernel: cs: IO port probe 0x0a00-0x0aff: excluding 0xa68-0xa6f 0xaf8-0xaff Jun 26 17:00:25 efi cardmgr[376]: initializing socket 0 Jun 26 17:00:25 efi kernel: cs: memory probe 0x0d0000-0x0dffff: clean. Jun 26 17:00:25 efi cardmgr[376]: socket 0: Serial or Modem Jun 26 17:00:25 efi cardmgr[376]: executing: 'modprobe serial_cs' Jun 26 17:00:26 efi kernel: tty02 at 0x03e8 (irq = 5) is a 8250 Jun 26 17:00:26 efi cardmgr[376]: executing: './serial start ttyS2' ============================================================== serial_cs identified only one channel and incorrectly shows a 8250 uart. This channel does not work nor do various settings with setserial (including uart=16550a and irq=0). the pcmcia bridge settings: ============================================================== [root@efi /root]# dump_i365 Intel PCIC probe: Vadem VG-468 found, 2 sockets Socket 0: Identification and revision = 0x83 Interface status = 0x7f [bvd1/stschg] [bvd2/spkr] [detect] [wrprot] [ready] [poweron] Power control = 0xd0 [output] [Vcc=5v] [Vpp off] Interrupt and general control = 0x65 [iocard] [irq=5] Card status change = 00 Card status change interrupt control = 0xf8 [detect] [irq = 15] Control register = 00 [active low] Misc register = 0x80 [unlock] Card detect and general control = 00 Global control = 00 Memory window 0: [ON] [WS1] [REG] start = 0x00d0, stop = 0x00d0, offset = 0x3f30 Memory window 1: [OFF] start = 0000, stop = 0000, offset = 0000 Memory window 2: [OFF] start = 0000, stop = 0000, offset = 0000 Memory window 3: [OFF] start = 0000, stop = 0000, offset = 0000 Memory window 4: [OFF] start = 0000, stop = 0000, offset = 0000 I/O window 0: [ON] start = 0x03e8, stop = 0x03ef I/O window 1: [OFF] start = 0000, stop = 0x0001 ============================================================== a dump_cis follows... ============================================================== [root@efi /root]# ./dump_cis Socket 0: dev_info NULL 0ns, 512b checksum 0x000c-0x0046 = 0xb3 attr_dev_info fn_specific 200ns, 64kb mfc { manfid 0x0104, 0x0070 vers_1 5.0, "Socket", "Dual I/O Card Rev 2.1" funcid serial_port [post] config base 0x0400 mask 0x0003 last_index 0x2d cftable_entry 0x0d [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x03f8-0x03ff [lines=16] [8bit] [range] irq mask 0xffff [level] cftable_entry 0x15 [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x02f8-0x02ff [lines=16] [8bit] [range] irq mask 0xffff [level] cftable_entry 0x1d [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x03e8-0x03ef [lines=16] [8bit] [range] irq mask 0xffff [level] cftable_entry 0x25 [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x02e8-0x02ef [lines=16] [8bit] [range] irq mask 0xffff [level] cftable_entry 0x2d [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x0000-0x0007 [lines=3] [8bit] irq mask 0xffff [level] }, { funcid serial_port [post] config base 0x0420 mask 0x0003 last_index 0x2d cftable_entry 0x0d [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x03f8-0x03ff [lines=16] [8bit] [range] irq mask 0xffff [level] cftable_entry 0x15 [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x02f8-0x02ff [lines=16] [8bit] [range] irq mask 0xffff [level] cftable_entry 0x1d [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x03e8-0x03ef [lines=16] [8bit] [range] irq mask 0xffff [level] cftable_entry 0x25 [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x02e8-0x02ef [lines=16] [8bit] [range] irq mask 0xffff [level] cftable_entry 0x2d [default] [rdybsy] [pwrdown] Vcc Vnom 5V Vmin 4500mV Vmax 5500mV Istatic 15mA Iavg 25mA Ipeak 2500uA Idown 20uA io 0x0000-0x0007 [lines=3] [8bit] irq mask 0xffff [level] } ============================================================== and a dump_cisreg.... which has an i/o error??? ============================================================== [root@efi /root]# dump_cisreg Socket 0 function 0: Config register base = 0x0400, mask = 0x0003 Configuration option register = 0x5f [level_req] [func_ena] [addr_decode] [ireq_ena] [index = 0x18] Card configuration and status register = 00 Socket 0 function 1: Config register base = 0x0420, mask = 0x0003 read config register: Input/output error Socket 1 function 0: Config register base = 0x0400, mask = 0x000b Configuration option register = 0x60 [level_req] [index = 0x20] Card configuration and status register = 00 Socket and copy register = 00 [socket = 0] [copy = 0] ============================================================== any help would be appreciated... TIA, john gwynne jsg@mrcday.com

1. It seems to be a new revision by David Hinds, 2000, Jul 11 (_ Feedback: Re: It seems to be a new revision by john gwynne, 2000, Jul 11

Question: Xircom Realport2 ISDN Adapter (R2I) Date: 2000, Jul 06 From: Mike Gerber mgerber

I'm not sure if that is the right forum (although there is none specific for ISDN adapters). OK, I'm currently running kernel 2.2.14-12 (RedHat build) with pcmcia version 3.1.8 and I'm interested in getting the "Xircom Realport2 ISDN Adapter" to work with Linux (This card is only ISDN, no eth or modem). Anyone had any luck? cardmgr says: Jun 29 10:04:59 thinkpad cardmgr[1701]: unsupported card in socket 0 Jun 29 10:04:59 thinkpad cardmgr[1701]: product info: "Xircom", "RealPort2 ISDN Adapter", "R2I", "1.00" Jun 29 10:04:59 thinkpad cardmgr[1701]: manfid: 0x0105, 0x200a function: 6 (network)

Question: ADVICE: Configuring my PCMCIA GSM Modem Date: 2000, Jul 09 From: F FrankC

Hi, As a Linux newbie, I'm trying to configure an unsupported PCMCIA GSM Modem card using RedHat 6.1-Linux 2.2.12-20 and pcmcia-cs-3.1.17 on a Compaq Armada 1750. But... I seem to be having a minor problem. When I modify the "test_modem" script to ATD<Phone Number> instead of ATI3, I get the following output: "Checking modem at /dev/ttyS1: Settings: /dev/ttyS1, UART: 16550A, Port: 0x02f8, IRQ: 3 Modem query timed out: trying polled mode. The modem is not working in polled mode." I've tried all sort of things including setting the irq to 0 but no avail - what am I doing wrong???? I've included a listing of some useful outputs of my current configuration. Any advice would be really welcome. Cheers, Frank [ ***** LSMOD OUTPUT ***** ] Module Size Used by serial_cs 5072 0 (unused) ds 6088 2 [serial_cs] i82365 21404 2 pcmcia_core 43648 0 [serial_cs ds i82365] opl3 11208 0 (unused) sb 33620 0 uart401 5968 0 [sb] sound 57240 0 [opl3 sb uart401] soundlow 300 0 [sound] soundcore 2372 6 [sb sound] [ ***** DMESG EXCERPT ***** ] ... Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS02 at 0x03e8 (irq = 4) is a 16550A ... Linux PCMCIA Card Services 3.1.17 kernel build: 2.2.12-20 #1 Mon Sep 27 10:40:35 EDT 1999 options: [pci] [cardbus] [apm] PCI routing table version 1.0 at 0xf09a0 00:11.0 -> irq 11 00:11.1 -> irq 11 Intel PCIC probe: TI 1225 rev 01 PCI-to-CardBus at slot 00:11, mem 0x7fffe000 host opts [0]: [ring] [pci + serial irq] [pci irq 11] [lat 66/176] [bus 2/2] host opts [1]: [ring] [pci + serial irq] [pci irq 11] [lat 66/176] [bus 3/3] ISA irqs (scanned) = 3,4,7,9,10,15 PCI status changes cs: IO port probe 0x02f8-0x02ff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. tty01 at 0x02f8 (irq = 3) is a 16550A [ ***** CARDCTL CONFIG *****] Socket 0: Vcc 5.0V Vpp1 0.0V Vpp2 0.0V interface type is "memory and I/O" irq 3 [exclusive] [level] Speaker output is enabled function 0: config base 0x0200 option 0x61 status 0x08 pin 0x00 ext 0x00 io 0x02f8-0x02ff [8bit] Socket 1: not configured [ ***** TEST_MODEM *****] Checking modem at /dev/ttyS1: Settings: /dev/ttyS1, UART: 16550A, Port: 0x02f8, IRQ: 3 ATI3 = 'OK ' The modem is operating normally. [ ***** TEST_SETUP *****] Current kernel: 2.2.12-20 #1 Mon Sep 27 10:40:35 EDT 1999 Module info from /lib/modules/2.2.12-20/pcmcia/pcmcia_core.o: Linux PCMCIA Card Services 3.1.17 kernel build: 2.2.12-20 #1 Mon Sep 27 10:40:35 EDT 1999 options: [pci] [cardbus] [apm] Startup options from /etc/sysconfig/pcmcia: PCMCIA=yes PCIC=i82365 PCIC_OPTS= CORE_OPTS= Checking current syslog files in /var/log: All PCMCIA messages are in /var/log/messages. Module status: The PCMCIA kernel modules are loaded correctly. Daemon status: cardmgr is running (process 366) Current socket status from /var/lib/pcmcia/stab: Socket 0: Serial or Modem 0 serial serial_cs 0 ttyS1 4 65 Socket 1: empty

1. Why did you want to modify test_modem this way? by David Hinds, 2000, Jul 10 (_ Agree: RE: Why did you want to modify test modem this way? by F, 2000, Jul 11

Question: Compex Linkport-Comm 56-E CTR21 V90 modem Date: 2000, Aug 09 From: Mitja Pufic RAVEer

Hello! I recently bought that modem with hope that it will work perfectly like the ethernet card EnetB from the same family. I discovered that inside is rockwells RCDL56ACFL chipset, and i now i am little scared that this is winmodem, how can i know that? well cardctl ident report: Socket 1: product info: "PC Card K56 Fax Modem", "RCDL56ACFL V.90 & K56flex", "021", "A" manfid: 0x0013, 0x0000 function: 2 (serial) and from /var/log/messages Aug 9 13:40:01 raindrop cardmgr[588]: initializing socket 1 Aug 9 13:40:01 raindrop cardmgr[588]: socket 1: EZLink 4109 Ethernet Aug 9 13:40:01 raindrop cardmgr[588]: executing: 'insmod /lib/modules/2.2.14/net/8390.o' Aug 9 13:40:01 raindrop cardmgr[588]: executing: 'insmod /lib/modules/2.2.14/pcmcia/pcnet_cs.o' Aug 9 13:40:01 raindrop kernel: eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:A0:0C:13:08:42 Aug 9 13:40:01 raindrop cardmgr[588]: executing: './network start eth0' Aug 9 13:40:02 raindrop cardmgr[588]: + SIOCADDRT: Invalid argument Aug 9 13:40:25 raindrop cardmgr[588]: initializing socket 0 Aug 9 13:40:25 raindrop cardmgr[588]: socket 0: Serial or Modem Aug 9 13:40:25 raindrop cardmgr[588]: executing: 'insmod /lib/modules/2.2.14/pcmcia/serial_cs.o port 0x03e8' like i don't know how to recognize winmodem, but i think that this one is real, so what are the next steps to finaly get it working like cardctl ident and status shows the card, but cat /var/stat/pcmcia/stab shows only ethernet card? any ideas? l'd be really glad if someone could help me out, thanks in advance mitja pufic raveer@kibla.org

1. Bad serial_cs parameters by David Hinds, 2000, Aug 09 (_ More: Compex Linkport-Comm 56-E CTR21 V90 modem 2 by Mitja Pufic, 2000, Aug 09 (_ IO port issue by David Hinds, 2000, Aug 09

Feedback: Nokia Card Phone 2.0 Date: 2000, Aug 11 From: Jochen Scharrlach <js@mgm-net.de>

Finally I got it working. The trick on my system was, that you must not talk to the second serial line at all - even setting the irq results in a hanging card until you do a "cardctl reset". This effect seems to occur only on my toshiba, on a Compaq everything works fine. My solution was to set "DEVICE=ignore" in serial.opts if an "ADDRESS=*,*,1" was requested and of course to exit the serial-script if "$DEVICE==ignore". Notebook: Toshiba 2180CDT with RedHat 6.2 dmesg: Intel PCIC probe: Toshiba ToPIC95-B rev 07 PCI-to-CardBus at slot 00:13, mem 0x68000000 host opts [0]: [slot 0xf0] [ccr 0x10] [cdr 0x86] [rcr 0x00] [no pci irq] [lat 168/176] [bus 20/20] host opts [1]: [slot 0xf0] [ccr 0x20] [cdr 0x86] [rcr 0x00] [no pci irq] [lat 168/176] [bus 21/21] ISA irqs (default) = 3,5,9,10 polling interval = 1000 ms cs: IO port probe 0x0100-0x04ff: clean. cs: memory proe 0x0d0000-0x0dffff: clean. [...] tty16 at 0x0100 (irq = 5) is a 16550A tty17 at 0x0108 (irq = 5) is a 8250 Card: Nokia Card Phone 2.0 (slot 1 above) [root@ezri ~]# uname -rv 2.2.16-3 #1 Mon Jun 19 18:49:25 EDT 2000 [root@ezri ~]# cardctl -V cardctl version 3.1.19

Question: Diehl/DIVA ISDN card Date: 2000, Aug 15 From: Rhys Morgan rmorgan

Hi, I have come across an ISDN Terminal Adapter card manufactured by a company called "G.Diehl ISDN GmbH", in about 1996. I would like to know how to find out if one of the existing drivers would function (serial_cs doesn't), without going through them one-by-one. I am using a Toshiba Tecra8000 with a RedHat 2.2.9 kernel, and version 3.1.12 of the pcmcia card services. For reference, the /var/log/messages file has the following relevent contents when I insert the card: Aug 15 14:31:51 localhost cardmgr[391]: re-loading config file Aug 15 14:31:51 localhost kernel: cs: IO port probe 0x1000-0x17ff: clean. Aug 15 14:31:51 localhost kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x330-0x337 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7 Aug 15 14:31:51 localhost kernel: cs: IO port probe 0x0a00-0x0aff: clean. Aug 15 14:32:10 localhost cardmgr[391]: initializing socket 1 Aug 15 14:32:10 localhost cardmgr[391]: socket 1: Anonymous Memory Aug 15 14:32:10 localhost cardmgr[391]: executing: 'insmod /lib/modules/2.2.9-17/pcmcia/sram_mtd.o' Aug 15 14:32:10 localhost cardmgr[391]: Common memory region at 0x0: Generic or SRAM Aug 15 14:32:10 localhost kernel: sram_mtd: common at 0x0, 2 mb, 250 ns Aug 15 14:32:10 localhost kernel: memory_cs: mem0: common 2 mb Aug 15 14:32:10 localhost cardmgr[391]: executing: 'insmod /lib/modules/2.2.9-17/pcmcia/memory_cs.o' Aug 15 14:32:10 localhost cardmgr[391]: executing: './memory start mem0' Aug 15 14:32:28 localhost cardmgr[391]: executing: './memory check mem0' Aug 15 14:32:28 localhost cardmgr[391]: shutting down socket 1 Aug 15 14:32:28 localhost cardmgr[391]: executing: './memory stop mem0' Aug 15 14:32:29 localhost cardmgr[391]: executing: 'rmmod memory_cs' Aug 15 14:32:29 localhost cardmgr[391]: executing: 'rmmod sram_mtd' And the /etc/pcmcia/config file entry looks like (as copied from the "cardctl ident" output): card "Diehl ISDN" version "ISDN-DIVA/PCM", "14.03.94", "1-1" bind "serial_cs" Thank you, Rhys Morgan

Question: COMpad-32B 4 port card is recognized as parallel Date: 2000, Aug 22 From: Felix Radensky felix

Hi, I'm running pcmcia-cs-3.1.19 on 2.2.16 kernel. My distro is Slackware-7.1. I've got problems with COMpad-32B 4 port serial card. cardmgr reconizes it as parallel port card and tries loading parport_cs module. I know that COMpad-32/85 dual port cards are supported. Is there anything I can do with a 4 port one ? Thanks in advance. Felix.

Sad: file transfer stalls at 115200 baud serial line speed Date: 2000, Aug 27 From: Michael Feig meikkel

I am having similar problems as previously posted here and on the Xircom list with large file transfers (ftp over PPP) stalling reproducibly at the same point. While there was no mention of this in the earlier posts this only seems to happen in my system when the serial line speed is set to 115200 baud. I have an Acer TravelMate 524TXV with an O2 Micro CardBus adapter running RedHat 6.2 with 2.2.16 kernel and PCMCIA version 3.1.19. I tried both a Xircom RealPort 56K as well as an ActionTec 56K Datalink PCMCIA card with the same problem. Using PCIC_OPTS="pci_csc=1 pci_int=1" in the PCMCIA options file (/etc/sysconfig/pcmcia) helps a little bit for the Xircom card but does not seem to do much for the Actiontec. "A little bit" means that the file transfer does not stall completely but continues very sluggishly after the stalling point and eventually completes. The only fix so far is reducing the serial line speed to 57600 which is not desirable for a 56K modem using compression. I have no idea at this point what else to try to get a 56K PCMCIA modem working with 115000 baud serial line speed and would be thankful for any suggestions. I am also not sure how to isolate further what component is causing the problem (serial_cs, pcmcia_core, pppd?). For reference various information from my system: lspci: 00:00.0 Host bridge: Acer Laboratories Inc. [ALi] M1621 (rev 05) 00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] M5247 (rev 01) 00:06.0 Multimedia audio controller: Acer Laboratories Inc. [ALi]: Unknown device 5451 (rev 01) 00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV] 00:0a.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08)00:10.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c3) 00:11.0 Bridge: Acer Laboratories Inc. [ALi] M7101 PMU 00:13.0 CardBus bridge: O2 Micro, Inc.: Unknown device 6933 (rev 01) 00:13.1 CardBus bridge: O2 Micro, Inc.: Unknown device 6933 (rev 01) 00:14.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage P/M Mobility AGP 2x (Rev. 64) dmesg: ... Linux PCMCIA Card Services 3.1.19 kernel build: 2.2.16-3 #11 Sat Aug 26 22:16:57 PDT 2000 options: [pci] [cardbus] [apm] [pnp] PCI routing table version 1.0 at 0xfb9d0 00:13.0 -> irq 11 00:13.1 -> irq 11 PnP: PNP BIOS installation structure at 0xc00f65b0 PnP: PNP BIOS version 1.0, entry at fa000:0, dseg at f0000 Intel PCIC probe: Unknown [1217 6933] rev 01 PCI-to-CardBus at slot 00:13, mem 0x68000000 host opts [0]: [pci irq 11] [lat 32/176] [bus 32/34] host opts [1]: [pci irq 11] [lat 32/176] [bus 35/37] ISA irqs (default) = 3,5,9 PCI status changes cs: IO port probe 0x1000-0x17ff: clean. cs: IO port probe 0x0100-0x04ff: clean. cs: IO port probe 0x0a00-0x0aff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. tty01 at 0x13f8 (irq = 3) is a 16550A ... /etc/sysconfig/pcmcia: PCMCIA=yes PCIC=i82365 PCIC_OPTS="pci_csc=1 pci_int=1" CORE_OPTS= /etc/pcmcia/config.opts: (unmodified from default) # # Local PCMCIA Configuration File # # System resources available for PCMCIA devices # include port 0x100-0x4ff, port 0x1000-0x17ff include memory 0xc0000-0xfffff include memory 0xa0000000-0xa0ffffff, memory 0x60000000-0x60ffffff # # Extra port range for IBM Token Ring # include port 0xa00-0xaff # # Resources we should not use, even if they appear to be available # # First built-in serial port exclude irq 4 # Second built-in serial port #exclude irq 3 # First built-in parallel port exclude irq 7 # PS/2 Mouse controller port, comment this out if you don't have a PS/2 # based mouse exclude irq 12 # # Examples of options for loadable modules # # To fix sluggish network with IBM ethernet adapter... #module "pcnet_cs" opts "mem_speed=600" # # Options for Xircom Netwave driver... #module "netwave_cs" opts "domain=0x100 scramble_key=0x0" # # Options for IBM Token Ring adapters #module "ibmtr_cs" opts "mmiobase=0xd0000 srambase=0xd4000"

Angry: PCMCIA works very very very slowly Date: 2000, Aug 28 From: Benson Fung bensonfung

Dear all, I have installed a PCI-PCMCIA adaptor(Cirrus PD6729) in my destop to connect the Nokia Cardphone 2.0. In fact, the card phone modem work fine under RH Linux 6.1. However, it works very very very slowly. Can anyone provide me a solution how to fix the problem? Right now, I am using pcmcia-cs 3.1.8. Do I need to upgrade it? Benson

1. Interrupt problem; you'll need a driver upgrade by David Hinds, 2000, Aug 28

Question: 3CXM656 - What is exactly a WinModem ? Date: 2000, Sep 26 From: Christian Gennerat c_gennerat

When I insert the modem, I get: cardmgr[369]: initializing socket 0 cardmgr[369]: unsupported card in socket 0 cardmgr[369]: product info: "3Com", "Megahertz 3CXM656", "Global Modem For Windows" cardmgr[369]: manfid: 0x0101, 0x003b function: 254 (null)) modprobe: can't locate module char-major-108 . In the cis, I have noticed that: -There is No funcid -The I/O address are not usual serial port addresses Can this be fixed with a hand-made cis ? What are the fundamental differencies between a WinModem, a TuxModem, and a standard modem?

1. You are out of luck... by David Hinds, 2000, Sep 26

Question: IBM V.90 PC Card Modem with XJACK ... funcid: 254 (null) Date: 2000, Nov 01 From: Tom Bradner wetclay

what's a fellow to do? I have an IBM ThinkPad 760E. Cardmgr fires up ok but didn't recognize the card. So I inserted the card in /etc/pcmcia/config and it was happy. After serial_cs is loaded it tells me, "serial_cs: IORequest = no more items". That is then followed by "cardmgr: get dev info on socket 1 failed : Resource temporarily unavailable". I have tried to glean what I can from some of the other postings. But alas, it may get down to either a different modem or some real work. One last point. As mentioned in the title, the funcid returns a value of 254 (null). Perhaps I should get the big rubber stamp out and print 'LOSER' on my forehead. But I'll wait until someone confirms my suspicions. Thanks Tom

[ Add Message ]  to: "PCMCIA Serial and Modem Issues"

[ Members ]  [ Subscribe ]  [ Admin Mode ] 
[ Show Frames ]  [ Help for HyperNews at pcmcia-cs.sourceforge.net 1.10 ]