Next-in-Thread Next Message

Sad Tecra 8100 & Ositech Jack of Spades - Help 

Forum: PCMCIA on Toshiba laptops
Date: 2000, Aug 05
From: Cristian Pavel cristian

Hi Dave and All,

I have:

Toshiba Tecra 8100 (320Mb memory)
Ositech Jack of Spades
Mandrake 7.1
pcmcia-cs-3.1.19

I think I'm close to have it up but I need some HELP. The card
looks like is started OK (got the 2 high beeps with both the
card in during boot or card inserted after boot; more, cardctl
commands: suspend resume reset eject and insert are working OK)
and the network is started for the localhost:

>ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:C0:E3:27:05:16
          inet addr:192.168.0.30 Bcast:192.168.0.255 Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          Interrupt:11 Base address:0x1100


But, I can not see any green light on my switch indicating
that the card is up (which I can get with the same identical
card & CAT5 cable when using WinNT and the driver provided by
Ositech for Micros..t).

If I try ">route add 192.162.0.10" I get: "SIOCADDRT: No such device"

At this point, after a couple of days of work_code_and_docs_study,
I decided to give up and ask for HELP.

Thanks

Cristian

--------------------------------------------------------------

a. My /etc/sysconfig/pcmcia is :

PCMCIA=yes
PCIC=i82365

b. My /etc/pcmcia/config.opts is:

#
# Local PCMCIA Configuration File
#

include port 0x100-0x477, port 0x1000-0x17ff
include memory 0xc0000-0xfffff
include memory 0xa0000000-0xa0ffffff

exclude irq 3
exclude irq 4
exclude irq 5
exclude irq 7
exclude irq 9
exclude irq 12
exclude irq 14
exclude irq 15

c. My /etc/sysconfig/network-scripts/networks.opts is

if [ -f /etc/sysconfig/network-scripts/ifcfg-eth0 ] ; then
        start_fn() {
                /sbin/ifup $1
        }

        stop_fn() {
                /sbin/ifdown $1
        }
fi

After boot info:

>dmesg

Linux PCMCIA Card Services 3.1.19
  kernel build: 2.2.15-4mdk #1 Wed May 10 15:31:30 CEST 2000
  options: [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xf0140
  00:0b.0 -> irq 11
  00:0b.1 -> irq 11
ds: no socket drivers loaded!
unloading PCMCIA Card Services
Linux PCMCIA Card Services 3.1.19
  kernel build: 2.2.15-4mdk #1 Wed May 10 15:31:30 CEST 2000
  options: [pci] [cardbus] [apm]
PCI routing table version 1.0 at 0xf0140
Intel PCIC probe:
  Toshiba ToPIC95-B rev 07 PCI-to-CardBus at slot 00:0b, mem 0x68000000
    host opts [0]: [slot 0xf0] [ccr 0x10] [cdr 0x86] [rcr 0xc000000] [pci irq 11] [lat 64/176] [bus 20/20]
    host opts [1]: [slot 0xf0] [ccr 0x20] [cdr 0x86] [rcr 0xc000000] [pci irq 11] [lat 64/176] [bus 21/21]
    ISA irqs (default) = 3,4,5,7,9,10,12 PCI status changes
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0100-0x0477: excluding 0x330-0x337 0x378-0x37f
cs: cb_alloc(bus 20): vendor 0x10b8, device 0x0006
ROM image dump:
  image 0: 0x000000-0x000bff, signature PCIR
epic100.c:v1.07h 8/18/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/epic100.html
cs: cb_config(bus 20)
  fn 0 bar 1: io 0x1100-0x11ff
  fn 0 bar 2: mem 0xa0041000-0xa0041fff
  fn 1 bar 1: io 0x1000-0x10ff
  fn 1 bar 2: mem 0xa0040000-0xa0040fff
  fn 0 rom: mem 0xa0030000-0xa003ffff
  fn 1 rom: mem 0xa0020000-0xa002ffff
  irq 11
cs: cb_enable(bus 20)
  bridge io map 0 (flags 0x21): 0x1000-0x11ff
  bridge mem map 0 (flags 0x1): 0xa0020000-0xa0041fff
epic_attach(bus 20, function 0)
eth0: <NULL> at 0x1100, IRQ 11, 00:c0:e3:27:05:16.
eth0: MII transceiver #1 control 3100 status 7809.
eth0: Autonegotiation advertising 01e1 link partner 0000.
serial_attach(device 14:00.1)
tty01 at 0x1000 (irq = 11) is a 16550A

>cat /var/log/messages
...
Aug 5 00:15:37 localhost pcmcia: Starting PCMCIA services:
Aug 5 00:15:37 localhost pcmcia: modules
Aug 5 00:15:37 localhost kernel: Linux PCMCIA Card Services 3.1.19
Aug 5 00:15:37 localhost kernel: kernel build: 2.2.15-4mdk #1 Wed May 10 15:31:30 CEST 2000
Aug 5 00:15:37 localhost kernel: options: [pci] [cardbus] [apm]
Aug 5 00:15:37 localhost kernel: PCI routing table version 1.0 at 0xf0140
Aug 5 00:15:37 localhost kernel: Intel PCIC probe:
Aug 5 00:15:37 localhost kernel: Toshiba ToPIC95-B rev 07 PCI-to-CardBus at slot 00:0b, mem 0x68000000
Aug 5 00:15:37 localhost kernel: host opts [0]: [slot 0xf0] [ccr 0x10] [cdr 0x86] [rcr 0xc000000] [pci irq 11] [lat 64/176] [bus 20/20]
Aug 5 00:15:37 localhost kernel: host opts [1]: [slot 0xf0] [ccr 0x20] [cdr 0x86] [rcr 0xc000000] [pci irq 11] [lat 64/176] [bus 21/21]
Aug 5 00:15:37 localhost kernel: ISA irqs (default) = 3,4,5,7,9,10,12 PCI status changes
Aug 5 00:15:37 localhost pcmcia: cardmgr.
Aug 5 00:15:37 localhost rc: Starting pcmcia succeeded
Aug 5 00:15:37 localhost cardmgr[410]: starting, version is 3.1.19
Aug 5 00:15:37 localhost cardmgr[410]: watching 2 sockets
Aug 5 00:15:37 localhost kernel: cs: IO port probe 0x1000-0x17ff: clean.
Aug 5 00:15:37 localhost kernel: cs: IO port probe 0x0100-0x0477: excluding 0x330-0x337 0x378-0x37f
Aug 5 00:15:38 localhost kernel: cs: cb_alloc(bus 20): vendor 0x10b8, device 0x0006
Aug 5 00:15:38 localhost cardmgr[410]: initializing socket 0
Aug 5 00:15:38 localhost cardmgr[410]: socket 0: Ositech Jack of Spades Fast Ethernet/Modem
Aug 5 00:15:38 localhost cardmgr[410]: executing: 'modprobe cb_enabler'
Aug 5 00:15:38 localhost cardmgr[410]: executing: 'modprobe epic_cb'
Aug 5 00:15:38 localhost kernel: epic100.c:v1.07h 8/18/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/epic100.html
Aug 5 00:15:38 localhost cardmgr[410]: executing: 'modprobe serial_cb'
Aug 5 00:15:38 localhost kernel: cs: cb_config(bus 20)
Aug 5 00:15:38 localhost kernel: fn 0 bar 1: io 0x1100-0x11ff
Aug 5 00:15:38 localhost kernel: fn 0 bar 2: mem 0xa0041000-0xa0041fff
Aug 5 00:15:38 localhost kernel: fn 1 bar 1: io 0x1000-0x10ff
Aug 5 00:15:38 localhost kernel: fn 1 bar 2: mem 0xa0040000-0xa0040fff
Aug 5 00:15:38 localhost kernel: fn 0 rom: mem 0xa0030000-0xa003ffff
Aug 5 00:15:38 localhost kernel: fn 1 rom: mem 0xa0020000-0xa002ffff
Aug 5 00:15:38 localhost kernel: irq 11
Aug 5 00:15:39 localhost kernel: eth0: <NULL> at 0x1100, IRQ 11, 00:c0:e3:27:05:16.
Aug 5 00:15:39 localhost kernel: eth0: MII transceiver #1 control 3100 status 7809.
Aug 5 00:15:39 localhost kernel: eth0: Autonegotiation advertising 01e1 link partner 0000.
Aug 5 00:15:39 localhost kernel: serial_attach(device 14:00.1)
Aug 5 00:15:39 localhost kernel: tty01 at 0x1000 (irq = 11) is a 16550A
Aug 5 00:15:38 localhost cardmgr[410]: executing: './network start eth0'
Aug 5 00:15:40 localhost cardmgr[410]: executing: './serial start ttyS1'
...

>cat /var/lib/pcmcia/stab
Socket 0: Ositech Jack of Spades Fast Ethernet/Modem
0 network epic_cb 0 eth0
0 serial serial_cb 0 ttyS1 4 65
Socket 1: empty 4 65
Socket 1: empty

>cardctl ident
Socket 0:
  product info: "Ositech", "Trumpcard:JoS Ethernet", "400062-002", "123456789abc"
  manfid: 0x0140, 0x0012
  function: 6 (network)
Socket 1:
  no product info available

>cardctl config
Socket 0:
  Vcc 3.3V Vpp1 3.3V Vpp2 3.3V
  interface type is "cardbus"
  irq 11 [exclusive] [level]
  function 0:
    io 0x1000-0x11ff [32bit]
  function 1:
    io 0x1000-0x11ff [32bit]
Socket 1:
  not configured

>cardctl status
Socket 0:
  3.3V CardBus card
  function 0: [ready]
  function 1: [ready]
Socket 1:
  no card

>cardctl ident
Socket 0:
  product info: "Ositech", "Trumpcard:JoS Ethernet", "400062-002", "123456789abc"
  manfid: 0x0140, 0x0012
  function: 6 (network)
Socket 1:
  no product info available

>cardctl config
Socket 0:
  Vcc 3.3V Vpp1 3.3V Vpp2 3.3V
  interface type is "cardbus"
  irq 11 [exclusive] [level]
  function 0:
    io 0x1000-0x11ff [32bit]
  function 1:
    io 0x1000-0x11ff [32bit]
Socket 1:
  not configured

>cardctl status
Socket 0:
  3.3V CardBus card
  function 0: [ready]
  function 1: [ready]
Socket 1:
  no card

>cat /proc/pci
...
  Bus 0, device 11, function 0:
    CardBus bridge: Toshiba ToPIC95 (rev 7).
      Slow devsel. Fast back-to-back capable. IRQ 11.
      Master Capable. Latency=64. Max Lat=4.
  Bus 0, device 11, function 1:
    CardBus bridge: Toshiba ToPIC95 (rev 7).
      Slow devsel. Fast back-to-back capable. IRQ 11.
      Master Capable. Latency=64. Min Gnt=128.Max Lat=4.

>cat /proc/modules
autofs 9604 1 (autoclean)
serial_cb 1148 1
epic_cb 10440 2
cb_enabler 2536 4 [serial_cb epic_cb]
ds 6444 2 [cb_enabler]
i82365 22948 2
pcmcia_core 45856 0 [cb_enabler ds i82365]
...


>cat /proc/interrupts
           CPU0
  0: 234892 XT-PIC timer
  1: 4248 XT-PIC keyboard
  2: 0 XT-PIC cascade
  8: 1 XT-PIC rtc
 11: 694 XT-PIC YMF744, i82365, eth0, usb-uhci
 12: 58481 XT-PIC PS/2 Mouse
 13: 1 XT-PIC fpu
 14: 5689 XT-PIC ide0
 15: 2 XT-PIC ide1
NMI: 0

------------------------------------------------------------------------------

Next-in-Thread Next Message

Messages Inline: 1 All Outline: 1 2 All

1. None I think this has recently been fixed by David Hinds, 2000, Aug 07
(_ Feedback Still not working by Cristian Pavel, 2000, Aug 08
(_ None Sorry, my mistake... by David Hinds, 2000, Aug 08
1. Feedback New error - unsupported card now! by Cristian Pavel, 2000, Aug 08
2. Ok Veni Vidi Vinci - It is working ! by Cristian Pavel, 2000, Aug 08

Add Message to: "Tecra 8100 & Ositech Jack of Spades - Help"

Members Subscribe Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10