Next-in-Thread Next Message

Question lucent ieee turbo pci adapter 

Forum: PCMCIA Wireless Network Adapter Issues
Date: 2000, Jan 31
From: Bob Cohen bonobob

kernel version: 2.2.12-20
pcmcia driver version: 3.1.8

I'm having problems with a Lucent Wavelan IEEE Turbo wireless networking card.
The wavelan is a pcmcia card that lucent bundles with a PCI adapter for
desktop machines. The PCI adapter is based on a TI 1225 chipset. The wavelan
configures properly, but interrupts appear not to be working, as I get
transmition timeout error messages, and packets are never received by the
driver. Also, I get error messages from card services saying:

cs: socket 1 timed out during reset

so, it seems that interrupts relating to card events also aren't happening.

I've tried various combinations of options pertaining to interrupts to the
i82365 pcic by modifying /etc/sysconfig/pcmcia, to no avail.

Here's what dmesg sez about the pcic probe:

Intel PCIC probe:
  TI 1225 PCI-to-CardBus at bus 2 slot 10, mem 0x68000000, 2 sockets
    host opts [0]: [pwr save] [isa irq] [no pci irq] [lat 168/176] [bus 32/34]
    host opts [1]: [pwr save] [isa irq] [no pci irq] [lat 168/176] [bus 35/37]
    ISA irqs (default) = 4,7,12 polling interval = 1000 ms
cs: IO port probe 0x1000-0x17ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x400-0x47f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.


Here's what dmesg sez about the wavelan card:

wvlan_cs: WaveLAN/IEEE PCMCIA driver v1.0.1
wvlan_cs: (c) Andreas Neuhaus <andy@fasta.fh-dortmund.de>
wvlan_cs: index 0x01: Vcc 5.0, irq 7, io 0x0100-0x013f
wvlan_cs: Registered netdevice wvlan0
wvlan_cs: Valid channels: 1 2 3 4 5 6 7 8 9 10 11
wvlan_cs: MAC address on wvlan0 is 00 60 1d 1e 78 83

Knowing nothing about any of this stuff, I played around a little with
lspci - here's what it says about the card:

02:0a.0 CardBus bridge: Texas Instruments: Unknown device ac1c (rev 01)
    Subsystem: Unknown device 104c:ac1c
    Flags: bus master, medium devsel, latency 168
    Memory at <ignored> (32-bit, non-prefetchable)
    Bus: primary=00, secondary=20, subordinate=22, sec-latency=176
    16-bit legacy interface ports at 0007

02:0a.1 CardBus bridge: Texas Instruments: Unknown device ac1c (rev 01)
    Subsystem: Unknown device 104c:ac1c
    Flags: bus master, medium devsel, latency 168
    Memory at <ignored> (32-bit, non-prefetchable)
    Bus: primary=00, secondary=23, subordinate=25, sec-latency=176
    16-bit legacy interface ports at 0007

Why doesn't it list an interrupt? When I do lspci -v -b, I get:

02:0a.0 CardBus bridge: Texas Instruments: Unknown device ac1c (rev 01)
    Subsystem: Unknown device 104c:ac1c
    Flags: bus master, medium devsel, latency 168, IRQ 255
    Memory at 68000000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=20, subordinate=22, sec-latency=176
    16-bit legacy interface ports at 0007

02:0a.1 CardBus bridge: Texas Instruments: Unknown device ac1c (rev 01)
    Subsystem: Unknown device 104c:ac1c
    Flags: bus master, medium devsel, latency 168, IRQ 255
    Memory at 68001000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=23, subordinate=25, sec-latency=176
    16-bit legacy interface ports at 0007

What is the implication of IRQ 255?

Any Suggestions?
Bob Cohen
bonobob@pacbell.net

Next-in-Thread Next Message

Messages Inline: 0 1

None 3.1.8 can't figure out the interrupt routing

Re: Question lucent ieee turbo pci adapter (Bob Cohen)
Date: 2000, Jan 31
From: David Hinds <dhinds@pcmcia.sourceforge.org>

Try again with pcmcia-cs-3.1.9; it should be able to deduce the PCI
interrupt assignment for the TI 1225 bridge.  Then set:

    PCIC_OPTS="irq_mode=0"

which tells the i82365 driver that the TI 1225 does not have any ISA
interrupt connections.

-- Dave

Sad didn't work

Re: None 3.1.8 can't figure out the interrupt routing (David Hinds)
Date: 2000, Jan 31
From: Bob Cohen bonobob

That didn't work. Looks like the minimal set of options necessary to get the wavelan module to load is:

 PCIC_OPTS="pci_int=1 irq_mode=0 pci_csc=1 pci_irq_list=7,7"

With this, the module loads, but again interrupts don't work (both card services, and the driver's interrupts). Also, irq7 seems to be the only one that works. How do you find out what irqs are valid for PCI? If I don't specify pci_irq_list, it doesn't work, so obviously probing isn't working.

This may be a red herring, but my bios has a field "reserve irq5", which allows irq5 to be devoted to "legacy isa devices" (whatever that means). I tried turning this on, and using isa interrupts - this didn't work either.

None Fixed...

Re: Sad didn't work (Bob Cohen)
Date: 2000, Feb 18
From: David Hinds <dhinds@pcmcia.sourceforge.org>

The interrupt routing problem is fixed in the latest (3.1.11) drivers.

-- Dave

Question "3.1.8 can't figure out the interrupt routing"

Re: None 3.1.8 can't figure out the interrupt routing (David Hinds)
Date: 2000, Feb 18
From: Gerald Richter richter

I have the same problem with a lucent WaveLan IEEE and a CL 6729 PCI Controller. I can access the card, but no interrupts are coming thru. The lspci shows that

"pin A routed to IRQ 11"

but I am not able to set anything to irq 11. When I don't specify an irq, the irq of the wvlan_cs driver is set to 5 and no irq is comming thru (/proc/interrupts shows 0).

What are the correct irq that the wvlan_cs driver should use, how can I debug this problem further?

Thanks for any help

Gerald

None This is a somewhat rare configuration

Re: Question "3.1.8 can't figure out the interrupt routing" (Gerald Richter)
Date: 2000, Feb 18
From: David Hinds <dhinds@pcmcia.sourceforge.org>

The current PCMCIA drivers can't handle the CL 6729 PCI card properly;
the drivers are not set up to allow use of PCI interrupts with this
bridge type.  Fixing this is in my queue of things to do, but I have
not gotten to it yet.

-- Dave

None RE: This is a somewhat rare configuration

Re: None This is a somewhat rare configuration (David Hinds)
Date: 2000, Feb 18
From: Gerald Richter richter

Hi,
>
> The current PCMCIA drivers can't handle the CL 6729 PCI card properly;
> the drivers are not set up to allow use of PCI interrupts with this
> bridge type.  Fixing this is in my queue of things to do, but I have
> not gotten to it yet.
>
thanks for your fast answer. Is there a PCI card (which chip should it
contain?)  that you know that handle interrupts correctly, or is this a
general problem with all PCI PCMCIA bridges?

Gerald

None It's true for most bridges like this

Re: None RE: This is a somewhat rare configuration (Gerald Richter)
Date: 2000, Feb 18
From: David Hinds <dhinds@pcmcia.sourceforge.org>

At the moment, there is no support for PCI-to-PCMCIA (16-bit-only)
bridges that are only wired for PCI interrupts.  PCI-to-CardBus
bridges are ok.

The only exception is the TI PCI1031 PCI-to-PCMCIA bridge, which is
more like a CardBus bridge with some of the CardBus support disabled.
The 3.1.11 drivers try to support this (I don't actually have one, so
I'm working with someone to verify that this works).

-- Dave

Idea Twosamples here...

Re: None 3.1.8 can't figure out the interrupt routing (David Hinds)
Date: 2000, Feb 25
From: Jean Tourrilhes jt

	David,

	I've got two samples here (PCI). I could lend you one
for debugging if you need. I also have one ISA sample which
work fine with 3.1.11 (but not with 2.3.47 ;-).
	By the way, I plan sooner or later to get the PCI
bridges into Linux box, so I'm interested as well...

	Regards,

	Jean

Feedback same problem for me!

Re: Question lucent ieee turbo pci adapter (Bob Cohen)
Date: 2000, Mar 26
From: Guillaum Dallaire gd

Hi,

I also have a PCI TI1225 from wavelan and the wavelan driver load, then I get :

wvlan_cs: wvlan0 Tx timed out! Resetting card

nothing to do, the card isn't usable!

(I use 3.11.13, kernel 2.2.14)

what finally happen ?

thanks!!

More Contact Andy...

Re: Feedback same problem for me! (Guillaum Dallaire)
Date: 2000, Mar 27
From: Jean Tourrilhes jt

	Please send a bug report to Andy. He will probably ask
you to enable debugging in the driver to know exactly what is
happening...

	Jean

None PCI interrupt routing?

Re: Feedback same problem for me! (Guillaum Dallaire)
Date: 2000, Mar 27
From: David Hinds <dhinds@pcmcia.sourceforge.org>

Can you post the PCMCIA startup messages from your system log?  This
could just be an interrupt routing problem.

-- Dave

More pcmcia startup

Re: None PCI interrupt routing? (David Hinds)
Date: 2000, Mar 30
From: Guillaum Dallaire gd

Hi,

Here is the log :

ar 27 14:09:33 localhost pcmcia: Starting PCMCIA services:

Mar 27 14:09:34 localhost pcmcia:  modules
Mar 27 14:09:34 localhost kernel: Linux PCMCIA Card Services 3.1.13 
Mar 27 14:09:34 localhost kernel:   kernel build: 2.2.14 #4 SMP lun mar 13 05:09:51 EST 2000 
Mar 27 14:09:34 localhost kernel:   options:  [pci] [cardbus] 
Mar 27 14:09:34 localhost kernel: PCI routing table version 1.0 at 0xf0b40 
Mar 27 14:09:34 localhost kernel:   unknown PCI interrupt router 10b9:1533 
Mar 27 14:09:34 localhost kernel: Intel PCIC probe:  
Mar 27 14:09:34 localhost kernel:   TI 1225 PCI-to-CardBus at slot 00:0a, mem 0x68000000 
Mar 27 14:09:34 localhost kernel:     host opts [0]: [isa irq] [no pci irq] [lat 32/176] [bus 32/34] 
Mar 27 14:09:34 localhost kernel:     host opts [1]: [isa irq] [no pci irq] [lat 32/176] [bus 35/37] 
Mar 27 14:09:34 localhost kernel:     ISA irqs (default) = 3,4,5,7,9,11,12,15 polling interval = 1000 ms 
Mar 27 14:09:34 localhost pcmcia:  cardmgr.
Mar 27 14:09:34 localhost rc: Starting pcmcia succeeded
Mar 27 14:09:34 localhost cardmgr[343]: starting, version is 3.1.13
Mar 27 14:09:34 localhost cardmgr[343]: watching 2 sockets
Mar 27 14:09:34 localhost kernel: cs: IO port probe 0x1000-0x17ff: clean. 
Mar 27 14:09:34 localhost kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x290-0x297 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7 
Mar 27 14:09:34 localhost kernel: cs: IO port probe 0x0a00-0x0aff: clean. 
Mar 27 14:09:34 localhost cardmgr[343]: initializing socket 0
Mar 27 14:09:34 localhost kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. 
Mar 27 14:09:34 localhost cardmgr[343]: socket 0: Lucent Technologies WaveLAN/IEEE Adapter
Mar 27 14:09:34 localhost cardmgr[343]: executing: 'insmod /lib/modules/2.2.14/pcmcia/wvlan_cs.o port_type=3 channel=3 station_name=dev-1'
Mar 27 14:09:34 localhost kernel: wvlan_cs: WaveLAN/IEEE PCMCIA driver v1.0.4 
Mar 27 14:09:34 localhost kernel: wvlan_cs: (c) Andreas Neuhaus <andy@fasta.fh-dortmund.de> 
Mar 27 14:09:35 localhost kernel: wvlan_cs: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f 
Mar 27 14:09:35 localhost kernel: wvlan_cs: Registered netdevice wvlan0 
Mar 27 14:09:35 localhost kernel: wvlan_cs: Valid channels: 1 2 3 4 5 6 7 8 9 10 11  
Mar 27 14:09:35 localhost kernel: wvlan_cs: MAC address on wvlan0 is 00 60 1d 03 8a df  
Mar 27 14:09:35 localhost cardmgr[343]: executing: './network start wvlan0'
Mar 27 14:09:35 localhost cardmgr[343]: initializing socket 1
Mar 27 14:09:35 localhost cardmgr[343]: socket 1: Anonymous Memory
Mar 27 14:09:36 localhost cardmgr[343]: executing: 'insmod /lib/modules/2.2.14/pcmcia/memory_cs.o'
Mar 27 14:09:36 localhost kernel: memory_cs: mem0: anonymous: unknown size 
Mar 27 14:09:36 localhost cardmgr[343]: executing: './memory start mem0'

None The "unknown interrupt router" problem

Re: More pcmcia startup (Guillaum Dallaire)
Date: 2000, Mar 30
From: David Hinds <dhinds@pcmcia.sourceforge.org>

> Mar 27 14:09:34 localhost kernel: PCI routing table version 1.0 at 0xf0b40 
> Mar 27 14:09:34 localhost kernel:   unknown PCI interrupt router 10b9:1533 

This is the crucial "bad thing".  This adapter card uses a PCI
interrupt to communicate with the system.  The Linux kernel does not
know how to deduce the interrupt routing for your host bridge, which
appears to be an Acer M1533.  Without that information, the drivers
report "no pci irq", and can't set up interrupt handling correctly.

I've contacted Acer to find out if I can get a datasheet for this host
bridge.

-- Dave

Sad I see the same thing..

Re: Question lucent ieee turbo pci adapter (Bob Cohen)
Date: 2000, Apr 10
From: Mark Geib geib

I help with a school installing a wireless network, all Linux. We just received some new machines and the WaveLan PCI adapters (20 of them). I have the same problem.

I will do whatever I can to help resolve this issue, loan cards and adapters, etc... just let me know.

Mark.

None This is mostly fixed; if not, then tell me more

Re: Sad I see the same thing.. (Mark Geib)
Date: 2000, Apr 10
From: David Hinds <dhinds@pcmcia.sourceforge.org>

This problem has already been fixed for most configurations.

You should try the current (3.1.13) PCMCIA driver package, and specify
PCIC_OPTS="irq_mode=0" in /etc/sysconfig/pcmcia.  If the problem
persists, then I need a lot more information about your specific
situation.  System log messages in particular.

-- Dave

Sad no luck, here is more info..

Re: None This is mostly fixed; if not, then tell me more (David Hinds)
Date: 2000, Apr 12
From: Mark Geib geib

No luck as yet. I set irq_mode=0. But now whenever I
insert the WaveLan card I hear one beep and the system
hangs until I remove the card.

Here is the output from messages.log, dmes, and an lspci.

Thanks ahead of time...

tail of messages.log from /var/log

Apr 12 11:31:30 localhost kernel: PCI: Probing PCI hardware 
Apr 12 11:31:30 localhost kernel: Linux NET4.0 for Linux 2.2 
Apr 12 11:31:30 localhost kernel: Based upon Swansea University Computer Society NET3.039 
Apr 12 11:31:30 localhost kernel: NET4: Unix domain sockets 1.0 for Linux NET4.0. 
Apr 12 11:31:30 localhost kernel: NET4: Linux TCP/IP 1.0 for NET4.0 
Apr 12 11:31:30 localhost kernel: IP Protocols: ICMP, UDP, TCP, IGMP 
Apr 12 11:31:30 localhost kernel: TCP: Hash tables configured (ehash 65536 bhash 65536) 
Apr 12 11:31:30 localhost kernel: Initializing RT netlink socket 
Apr 12 11:31:30 localhost kernel: Starting kswapd v 1.5  
Apr 12 11:31:30 localhost kernel: Detected PS/2 Mouse Port. 
Apr 12 11:31:30 localhost kernel: Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled 
Apr 12 11:31:30 localhost kernel: pty: 256 Unix98 ptys configured 
Apr 12 11:31:30 localhost kernel: apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9) 
Apr 12 11:31:30 localhost kernel: Real Time Clock Driver v1.09 
Apr 12 11:31:30 localhost kernel: RAM disk driver initialized:  16 RAM disks of 4096K size 
Apr 12 11:31:30 localhost kernel: PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=2411 
Apr 12 11:31:30 localhost kernel: PCI_IDE: not 100% native mode: will probe irqs later 
Apr 12 11:31:30 localhost kernel:     ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio 
Apr 12 11:31:30 localhost kernel:     ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio 
Apr 12 11:31:30 localhost kernel: hda: Maxtor 90651U2, ATA DISK drive 
Apr 12 11:31:30 localhost kernel: hdc: SAMSUNG CD-ROM SN-124, ATAPI CDROM drive 
Apr 12 11:31:30 localhost kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 
Apr 12 11:31:30 localhost kernel: ide1 at 0x170-0x177,0x376 on irq 15 
Apr 12 11:31:30 localhost kernel: hda: Maxtor 90651U2, 6149MB w/512kB Cache, CHS=784/255/63 
Apr 12 11:31:30 localhost kernel: hdc: ATAPI 24X CD-ROM drive, 128kB Cache 
Apr 12 11:31:30 localhost kernel: Uniform CDROM driver Revision: 2.56 
Apr 12 11:31:30 localhost kernel: Floppy drive(s): fd0 is 1.44M 
Apr 12 11:31:30 localhost kernel: FDC 0 is a National Semiconductor PC87306 
Apr 12 11:31:30 localhost kernel: md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12 
Apr 12 11:31:30 localhost kernel: raid5: measuring checksumming speed 
Apr 12 11:31:30 localhost kernel: raid5: MMX detected, trying high-speed MMX checksum routines 
Apr 12 11:31:30 localhost kernel:    pII_mmx   :  1109.472 MB/sec 
Apr 12 11:31:30 localhost kernel:    p5_mmx    :  1165.479 MB/sec 
Apr 12 11:31:30 localhost kernel:    8regs     :   855.726 MB/sec 
Apr 12 11:31:30 localhost kernel:    32regs    :   480.060 MB/sec 
Apr 12 11:31:30 localhost kernel: using fastest function: p5_mmx (1165.479 MB/sec) 
Apr 12 11:31:30 localhost kernel: scsi : 0 hosts. 
Apr 12 11:31:30 localhost kernel: scsi : detected total. 
Apr 12 11:31:30 localhost kernel: md.c: sizeof(mdp_super_t) = 4096 
Apr 12 11:31:30 localhost kernel: Partition check: 
Apr 12 11:31:30 localhost kernel:  hda: hda1 hda2 < hda5 hda6 > 
Apr 12 11:31:30 localhost kernel: RAMDISK: Compressed image found at block 0 
Apr 12 11:31:30 localhost kernel: autodetecting RAID arrays 
Apr 12 11:31:30 localhost kernel: autorun ... 
Apr 12 11:31:30 localhost kernel: ... autorun DONE. 
Apr 12 11:31:30 localhost kernel: VFS: Mounted root (ext2 filesystem). 
Apr 12 11:31:30 localhost kernel: autodetecting RAID arrays 
Apr 12 11:31:30 localhost kernel: autorun ... 
Apr 12 11:31:30 localhost kernel: ... autorun DONE. 
Apr 12 11:31:30 localhost kernel: VFS: Mounted root (ext2 filesystem) readonly. 
Apr 12 11:31:30 localhost kernel: change_root: old root has d_count=1 
Apr 12 11:31:30 localhost kernel: Trying to unmount old root ... okay 
Apr 12 11:31:30 localhost kernel: Freeing unused kernel memory: 64k freed 
Apr 12 11:31:30 localhost kernel: Adding Swap: 24056k swap-space (priority -1) 
Apr 12 11:31:30 localhost atd: atd startup succeeded
Apr 12 11:31:31 localhost crond: crond startup succeeded
Apr 12 11:31:31 localhost pcmcia: Starting PCMCIA services:
Apr 12 11:31:31 localhost pcmcia:  modules
Apr 12 11:31:31 localhost kernel: Linux PCMCIA Card Services 3.1.13 
Apr 12 11:31:31 localhost kernel:   kernel build: 2.2.12-20 #1 Mon Sep 27 10:40:35 EDT 1999 
Apr 12 11:31:31 localhost kernel:   options:  [pci] [cardbus] [apm] [pnp] 
Apr 12 11:31:31 localhost kernel: PCI routing table version 1.0 at 0xfbc40 
Apr 12 11:31:31 localhost kernel:   01:07.0 -> irq 9 
Apr 12 11:31:31 localhost kernel:   01:07.1 -> irq 9 
Apr 12 11:31:31 localhost kernel: PnP: PNP BIOS installation structure at 0xc00fe2d0 
Apr 12 11:31:31 localhost kernel: PnP: PNP BIOS version 1.0, entry at f0000:e2f4, dseg at 40 
Apr 12 11:31:31 localhost kernel: Intel PCIC probe:  
Apr 12 11:31:31 localhost kernel:   TI 1225 PCI-to-CardBus at slot 01:07, mem 0x68000000 
Apr 12 11:31:31 localhost kernel:     host opts [0]: [pci only] [pci irq 9] [lat 64/176] [bus 32/34] 
Apr 12 11:31:31 localhost kernel:     host opts [1]: [pci only] [pci irq 9] [lat 64/176] [bus 35/37] 
Apr 12 11:31:31 localhost kernel:     PCI card interrupts, PCI status changes 
Apr 12 11:31:31 localhost pcmcia:  cardmgr.
Apr 12 11:31:31 localhost cardmgr[355]: starting, version is 3.1.13
Apr 12 11:31:31 localhost rc: Starting pcmcia succeeded
Apr 12 11:31:31 localhost cardmgr[355]: watching 2 sockets
Apr 12 11:31:31 localhost kernel: cs: IO port probe 0x0c00-0x0cff: clean. 
Apr 12 11:31:31 localhost kernel: cs: IO port probe 0x0800-0x08ff: clean. 
Apr 12 11:31:31 localhost kernel: cs: IO port probe 0x0100-0x04ff: clean. 
Apr 12 11:31:31 localhost kernel: cs: IO port probe 0x0a00-0x0aff: clean. 
Apr 12 11:31:31 localhost inet: inetd startup succeeded
Apr 12 11:31:31 localhost lpd: lpd startup succeeded
Apr 12 11:31:31 localhost keytable: Loading keymap: Loading system font: 
Apr 12 11:31:31 localhost rc: Starting keytable succeeded
Apr 12 11:31:32 localhost sendmail: sendmail startup succeeded
Apr 12 11:31:33 localhost gpm: gpm startup succeeded
Apr 12 11:31:33 localhost xfs: xfs startup succeeded
Apr 12 11:31:33 localhost linuxconf: Linuxconf final setup
Apr 12 11:31:33 localhost xfs: Warning: The directory "/usr/X11R6/lib/X11/fonts/100dpi" does not exist. 
Apr 12 11:31:33 localhost xfs:          Entry deleted from font path. 
Apr 12 11:31:34 localhost kernel: cs: socket 1 timed out during reset 
Apr 12 11:31:35 localhost rc: Starting linuxconf succeeded
Apr 12 11:31:43 localhost PAM_pwdb[484]: (login) session opened for user root by LOGIN(uid=0)
Apr 12 11:31:52 localhost cardmgr[355]: initializing socket 0
Apr 12 11:31:52 localhost cardmgr[355]: socket 0: Lucent Technologies WaveLAN/IEEE
Apr 12 11:31:52 localhost kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. 
Apr 12 11:31:52 localhost cardmgr[355]: executing: 'insmod /lib/modules/2.2.12-20/pcmcia/wavelan2_cs.o'
Apr 12 11:31:54 localhost kernel: eth0: WaveLAN/IEEE, HCF failure: "Card not found (ejected unexpectedly)" 
Apr 12 11:31:54 localhost cardmgr[355]: get dev info on socket 0 failed: No such device
Apr 12 11:31:58 localhost cardmgr[355]: shutting down socket 0
Apr 12 11:31:58 localhost cardmgr[355]: executing: 'rmmod wavelan2_cs'

dmesg output

Linux version 2.2.12-20 (root@porky.devel.redhat.com) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Sep 27 10:40:35 EDT 1999
Detected 498488945 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 496.44 BogoMIPS
Memory: 61388k/64128k available (1008k kernel code, 412k reserved, 976k data, 64k init)
DENTRY hash table entries: 262144 (order: 9, 2097152 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium III (Katmai) stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfc0ce
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 65536 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5 
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
Real Time Clock Driver v1.09
RAM disk driver initialized:  16 RAM disks of 4096K size
PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=2411
PCI_IDE: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 90651U2, ATA DISK drive
hdc: SAMSUNG CD-ROM SN-124, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: Maxtor 90651U2, 6149MB w/512kB Cache, CHS=784/255/63
hdc: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.56
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
   pII_mmx   :  1109.472 MB/sec
   p5_mmx    :  1165.479 MB/sec
   8regs     :   855.726 MB/sec
   32regs    :   480.060 MB/sec
using fastest function: p5_mmx (1165.479 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
 hda: hda1 hda2 < hda5 hda6 >
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem).
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 64k freed
Adding Swap: 24056k swap-space (priority -1)
Linux PCMCIA Card Services 3.1.13
  kernel build: 2.2.12-20 #1 Mon Sep 27 10:40:35 EDT 1999
  options:  [pci] [cardbus] [apm] [pnp]
PCI routing table version 1.0 at 0xfbc40
  01:07.0 -> irq 9
  01:07.1 -> irq 9
PnP: PNP BIOS installation structure at 0xc00fe2d0
PnP: PNP BIOS version 1.0, entry at f0000:e2f4, dseg at 40
Intel PCIC probe: 
  TI 1225 PCI-to-CardBus at slot 01:07, mem 0x68000000
    host opts [0]: [pci only] [pci irq 9] [lat 64/176] [bus 32/34]
    host opts [1]: [pci only] [pci irq 9] [lat 64/176] [bus 35/37]
    PCI card interrupts, PCI status changes
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: socket 1 timed out during reset
cs: memory probe 0xa0000000-0xa0ffffff: clean.
eth0: WaveLAN/IEEE, HCF failure: "Card not found (ejected unexpectedly)"
VFS: Disk change detected on device fd(2,0)


output of lspci -vv


00:00.0 Host bridge: Intel Corporation: Unknown device 7124 (rev 03)
	Subsystem: Unknown device 1028:00b4
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0 set

00:01.0 VGA compatible controller: Intel Corporation: Unknown device 7125 (rev 03)
	Subsystem: Unknown device 1028:00b4
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at f4000000 (32-bit, prefetchable)
	Region 1: Memory at ff000000 (32-bit, non-prefetchable)
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- AuxPwr- DSI+ D1- D2- PME-
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1e.0 PCI bridge: Intel Corporation: Unknown device 2418 (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fe000000-feffffff
	Prefetchable memory behind bridge: f9000000-f9ffffff
	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation: Unknown device 2410 (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set

00:1f.1 IDE interface: Intel Corporation: Unknown device 2411 (rev 02) (prog-if 80)
	Subsystem: Unknown device 8086:2411
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Region 4: I/O ports at ffa0

00:1f.2 USB Controller: Intel Corporation: Unknown device 2412 (rev 02)
	Subsystem: Unknown device 8086:2412
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Interrupt: pin D routed to IRQ 11
	Region 4: I/O ports at ff80

00:1f.3 Class 0c05: Intel Corporation: Unknown device 2413 (rev 02)
	Subsystem: Unknown device 8086:2413
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin B routed to IRQ 10
	Region 4: I/O ports at ecd0

01:07.0 CardBus bridge: Texas Instruments: Unknown device ac1c (rev 01)
	Subsystem: Unknown device 104c:ac1c
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 set, cache line size 08
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at <ignored> (32-bit, non-prefetchable)
	Bus: primary=00, secondary=20, subordinate=22, sec-latency=176
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0007

01:07.1 CardBus bridge: Texas Instruments: Unknown device ac1c (rev 01)
	Subsystem: Unknown device 104c:ac1c
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 set, cache line size 08
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at <ignored> (32-bit, non-prefetchable)
	Bus: primary=00, secondary=23, subordinate=25, sec-latency=176
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0007
lucent ieee turbo pci adapter


Members Subscribe No Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10
[ Edit This Forum ]