Next-in-Thread Next Message

None Re: Need more detailed information 

Forum: Xircom PCMCIA Ethernet Adapter Issues
Re: Question RBEM56G-100 & Red Hat 6.2 (Marco A. Calamari)
Re: None Need more detailed information (David Hinds)
Date: 2000, May 04
From: Marco A. Calamari marcoc

At 11.10 03/05/00 -0700, David Hinds wrote:f you reply to this message at 
HyperNews@pcmcia.sourceforge.org, include:
In-Reply-To: <20000503112308.K19394@valinux.com>

....

>You say you get "an error" when you transmit packets.  What does that
>mean?  Is the error in your system log?  Are there any other messages
>from the driver in your system log?
>
>I don't understand how the packet count can rise, but also "all
>packets read are dropped".

First, sorry for the bad style of my previous posting,
  that was written in hurry.

The firmware revision of the pcmcia is now 2.66, but nothing change.

I mean that, using ifconfig, I see the packet count of dropped packet
  rising.

Attached, the messages from ifconfig, the output from lsmod,
  and the boot messages about the pcmcia&network

[root@ef19 /root]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:10:A4:E9:5D:0B
           inet addr:161.27.167.181  Bcast:161.27.167.255  Mask:255.255.255.128
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:0 errors:0 dropped:349 overruns:0 frame:0
           TX packets:0 errors:1 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:100
           Interrupt:3 Base address:0x200

lo        Link encap:Local Loopback
           inet addr:127.0.0.1  Mask:255.0.0.0
           UP LOOPBACK RUNNING  MTU:3924  Metric:1
           RX packets:15 errors:0 dropped:0 overruns:0 frame:0
           TX packets:15 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0


           [root@ef19 /root]# lsmod
           Module                  Size  Used by
           serial_cb               1080   1
           tulip_cb               30924   2
           cb_enabler              2568   4  [serial_cb tulip_cb]
           ds                      6696   2  [cb_enabler]
           i82365                 29800   2
           pcmcia_core            44480   0  [cb_enabler ds i82365]
           nls_iso8859-1           2240   1  (autoclean)
           nls_cp437               3748   1  (autoclean)
           vfat                    9276   1  (autoclean)
           fat                    30336   1  (autoclean) [vfat]
           esssolo1               20720   0
           soundcore               2628   4  [esssolo1]
           [root@ef19 /root]#


May  4 10:26:41 ef19 network: Setting network parameters succeeded
May  4 10:26:42 ef19 network: Bringing up interface lo succeeded
May  4 10:26:42 ef19 insmod: /lib/modules/2.2.14-5.0/pcmcia/ds.o: 
init_module: Device or resource busy
May  4 10:26:42 ef19 ifup: Delaying eth0 initialization.
May  4 10:26:42 ef19 network: Bringing up interface eth0 failed
May  4 10:26:42 ef19 portmap: portmap startup succeeded
May  4 10:26:42 ef19 random: Initializing random number generator succeeded
May  4 10:26:45 ef19 crond: crond startup succeeded
May  4 10:26:45 ef19 pcmcia: Starting PCMCIA services:
May  4 10:26:46 ef19 pcmcia:  modules
May  4 10:26:46 ef19 kernel: Linux PCMCIA Card Services 3.1.8
May  4 10:26:46 ef19 kernel:   kernel build: 2.2.14-5.0 #1 Tue Mar 7 
21:07:39 EST 2000
May  4 10:26:46 ef19 kernel:   options:  [pci] [cardbus] [apm]
May  4 10:26:46 ef19 kernel: Intel PCIC probe:
May  4 10:26:46 ef19 kernel:   O2Micro OZ6832/OZ6833 PCI-to-CardBus at bus 
0 slot 19, mem 0x68000000, 2 sockets
May  4 10:26:46 ef19 kernel:     host opts [0]: [a 44] [b a1] [c 20] [d 06] 
[mhpg 18] [fifo 00] [e 28] [no pci irq] [lat 32/176] [bus 32/34]
May  4 10:26:46 ef19 kernel:     host opts [1]: [a 44] [b ad] [c 20] [d 06] 
[mhpg 18] [fifo 00] [e 28] [no pci irq] [lat 32/176] [bus 35/37]
May  4 10:26:46 ef19 kernel:     ISA irqs (default) = 3,4,7,11,12 polling 
interval = 1000 ms
May  4 10:26:46 ef19 pcmcia:  cardmgr.
May  4 10:26:46 ef19 cardmgr[349]: starting, version is 3.1.8
May  4 10:26:46 ef19 rc: Starting pcmcia succeeded
May  4 10:26:46 ef19 cardmgr[349]: watching 2 sockets
May  4 10:26:46 ef19 kernel: cs: IO port probe 0x1000-0x17ff: clean.
May  4 10:26:46 ef19 kernel: cs: IO port probe 0x0100-0x04ff: excluding 
0x378-0x37f 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
May  4 10:26:46 ef19 kernel: cs: IO port probe 0x0a00-0x0aff: clean.
May  4 10:26:46 ef19 kernel: cs: cb_alloc(bus 35): vendor 0x115d, device 0x0003
May  4 10:26:46 ef19 cardmgr[349]: initializing socket 1
May  4 10:26:46 ef19 cardmgr[349]: socket 1: Xircom CardBus 10/100 Ethernet 
+ 56K Modem
May  4 10:26:46 ef19 lpd: lpd startup succeeded
May  4 10:26:46 ef19 lpd[363]: restarted
May  4 10:26:46 ef19 cardmgr[349]: executing: 'insmod 
/lib/modules/2.2.14-5.0/pcmcia/cb_enabler.o'
May  4 10:26:46 ef19 cardmgr[349]: executing: 'insmod 
/lib/modules/2.2.14-5.0/pcmcia/tulip_cb.o'
May  4 10:26:46 ef19 cardmgr[349]: executing: 'insmod 
/lib/modules/2.2.14-5.0/pcmcia/serial_cb.o'
May  4 10:26:46 ef19 kernel: cs: cb_config(bus 35)
May  4 10:26:46 ef19 kernel:   fn 0 bar 2: mem 0x60013000-0x600137ff
May  4 10:26:46 ef19 kernel:   fn 0 bar 3: mem 0x60012000-0x600127ff
May  4 10:26:46 ef19 kernel:   fn 1 bar 1: io 0x280-0x287
May  4 10:26:46 ef19 kernel:   fn 1 bar 2: mem 0x60011000-0x600117ff
May  4 10:26:46 ef19 kernel:   fn 1 bar 3: mem 0x60010000-0x600107ff
May  4 10:26:46 ef19 kernel:   fn 0 bar 1: io 0x200-0x27f
May  4 10:26:46 ef19 kernel:   fn 0 rom: mem 0x6000c000-0x6000ffff
May  4 10:26:47 ef19 kernel:   fn 1 rom: mem 0x60008000-0x6000bfff
May  4 10:26:47 ef19 kernel: tulip_attach(bus 35, function 0)
May  4 10:26:47 ef19 kernel: tulip.c:v0.91 4/14/99 
becker@cesdis.gsfc.nasa.gov (modified by danilo@cs.uni-magdeburg.de for 
XIRCOM CBE, fixed by Doug Ledford)
May  4 10:26:47 ef19 kernel: eth0: Xircom Cardbus Adapter (DEC 21143 
compatible mode) rev 3 at 0x200, 00:10:A4:E9:5D:0B, IRQ 3.
May  4 10:26:47 ef19 kernel: eth0:  MII transceiver #0 config 3100 status 
7809 advertising 01e1.
May  4 10:26:47 ef19 kernel: serial_attach(bus 35, fn 1)


> > Also using xirc2ps_cs give no change
>
>That's not possible (that there could be no change): you can't use
>xirc2ps_cs with a CardBus card.  You would get low beeps, error
>messages in your system log, etc.

I mean that in this situation nothing changed (I know that there
  are two pccard driver).

           [root@ef19 /root]# lsmod
           Module                  Size  Used by
           serial_cb               1080   1
           tulip_cb               30924   2
           cb_enabler              2568   4  [serial_cb tulip_cb]
           xirc2ps_cs             13856   0  (autoclean) (unused)
           ds                      6696   2  [cb_enabler xirc2ps_cs]
           i82365                 29800   2
           pcmcia_core            44480   0  [cb_enabler xirc2ps_cs ds i82365]
           nls_iso8859-1           2240   1  (autoclean)
           nls_cp437               3748   1  (autoclean)
           vfat                    9276   1  (autoclean)
           fat                    30336   1  (autoclean) [vfat]
           esssolo1               20720   0
           soundcore               2628   4  [esssolo1]

Thanks a lot and have a good day.   Marco





* Mac (Marco A. Calamari) marcoc@dada.it  www.dada.it/marcoc *
* PGP RSA: ED84 3839 6C4D 3FFE 389F 209E 3128 5698           *
* DSS/DH:  8F3E 5BAE 906F B416 9242 1C10 8661 24A9 BFCE 822B *

Next-in-Thread Next Message

Select this message: Re: Need more detailed information

Messages Inline: 1 All Outline: 1 2 All

1. None SOLUTION ! by Marco A. Calamari, 2000, May 05

Message Administration

This form allows you to delete, move, or copy one or more messages. You can move messages by copying and deleting the original. The action will be applied to the messages you select above and all replies to those selected messages.


If you want to copy or move messages, specify the HyperNews path of a destination forum or message that all messages will be copied or moved to. The destination must already exist, so maybe create it first.

Path of Destination (a Forum or Message): (e.g. "test")

Notify Subscribers at destination
NO


If you want to delete messages (the default), specify that here. If you want to move messages, you need to delete the original messages; placeholders will be left pointing to where they were moved.

Delete Messages
NO


Caution: After deleteing messages (the default), if you have not copied them (i.e. no destination above), then the selected messages are not be recoverable.

Members Subscribe No Admin Mode Show Frames Help for HyperNews at pcmcia-cs.sourceforge.net 1.10
[ Edit This Forum ]